Item Description Providing & Placing Waiting Chair Three Seater of Overall Size (in cm): 169.5W x 63.8D x 44.1SH & 78.5H Seat shell should be welded assembly of seat back and side frame. Seat and back should be made up of 0.12±0.013 cm thk CR Steele sheet with oblong perforation. Seat shell should be welded to sideframe of size 3.2±0.05 cm x 0.5±0.05 cm thk HR Steel. Welded assembly should be powder coated (DFT 40-60 microns). *Seat Size: 47.8W x 44.6D cm*Back Size: 41.6W x 23.0H cm Understructure assembly should consisit of connecting beam and leg assembly made of MS ERW oblong tube of size 7.5±0.03 cm x 2.5±0.03 cm x 0.2±0.016 cm thk. The welded structure assembly should be powder coated (DFT 40-60 microns). The Leg assembly should be fitted with shoe and levelers in nylon. The Leg structure should be designed with minimal area of contact close to ground providing easy access for cleaing purposes.The shoes fitted to leg assembly help in aligning the sutructure for back to back arrangements. Levellers take care of uneven flooring. Connecting beam should be fitted with snap locking end cap. It should also aids in side by side understructure alignment. Armrest assemby should consist of armrest frame and armrest pad. The armrest frame should be made up of size 3.175±0.05 cm x 0.47±0.027 cm thk HR steel and it should be powder coated (DFT 40-60 microns). Armrest pad should be injection moulded in Nylon and should be fitted onto the armrest frame. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam should be designed with contoured lumbar support for extra comfort. The seat should have extra thick foam on front edge to give comfort to popliteal area. *BACK SIZE : 47.5 cm (W) x 69.5 cm (H) *SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) POLYURETHANE FOAM: The Polyurethane foam should be moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 at 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM : The mechanism should be designed with the following features: 360° revolving type, Upright position locking, Tilt tension adjustment & Seat/back tilting ratio of 1:3 (60 seat tilt/180 back tilt) PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment should have an adjustment stroke of 12.0 cm. TELESCOPIC BELLOW ASSEMBLY : The bellow should be 3-piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY : The pedestal should be injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal should be 66.0cm pitch-center dia. (76.0 cm with castors.) TWIN WHEEL CASTORS : The twin wheel castors should be injection moulded in Black Nylon. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Main Table of Overall Size (in mm): 1350W x 750D x 750H The table top should be in white cedar, side panels in black while the modesty panel in a combination of black & white cedar. Tops / Worksurfaces : (White Cedar) Made from 18mm thick PLB with PVC lipping. Side Panels: (Black) Made from 18mm thick PLT with PVC lipping. Modesty Panel: Made from 18mm thick PLT with PVC lipping. Bigger upper panel in Black and smaller lower panel in white Cedar. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Level2 & Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Library Chair of Overall Size (in cm): 43.5W x 56.5D x 87.5H & 48.0SH SEAT/BACK ASSEMBLY: The seat and back should be made from chemically treated and seasoned wood, upholstered with plywood, black leather-cloth, and U-foam. *BACK SIZE: 38.5W x 27.0cm (H). *SEAT SIZE: 38.5W x 40.0cm (D). UNDERSTRUCTURE ASSEMBLY: The understructure assembly is a cantilever type frame made of dia. 2.54cm. (1?) x 14BG. thick M.S. E.R.W. tube and powder coated. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Library Table of Overall Size (in mm): 1800W x 900D x 740H Top should be made of 25mm Thick Pre-laminated particle board (PLB) with 2mm Thick PVC Edge Beading. C-Frames should be 1.6mm thick M.S Cframe supporting the Top. The table should have 4 legs made of Electric Resistant Welded prime quality CRCA steel round tubular frame of Dia 38.1 x 1.6mm thick M.S ERW tube. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Level2 & Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Three Seater Desk Bench of Overall Size (in mm): 1800W x 895D x 750H Top Panel: 1800mm (L) x 378mm (W) x 18mm thk PLB Seat Panel: 1800mm (L) x 335mm (W) x 18mm thk PLB Back Panel: 1800mm (L) x 265mm (W) x 18mm thk PLT Bench Height: 750mm Seat Height: 437mm Leg Assembly: U/S MS SQ Tubes 25.4 x 1.2mm thk Tops (Desk panel Seat, Back): The panels should be made from 18 mm thk MDF Boards with PVC edge banding on all sides. Understructure should be made of 25.4 x 25.4 mm x1.2 mm thk powder coated ERW tubes at base which should be welded to the desk and seat supports that are made of 1.0 mm thk powder coated MS ?C? sections. Stiffeners that are provided between the 2 vertical frames at base and back of seat should be made from 25.4 x25.4 x1.2 mm thk powder coated ERW tubes. The tubes should be closed with plastic caps. Additional horizontal supports of 1.5 mm thk powder coated MS ?C? sections should be placed below the desk and seat to add to the rigidity of the structure. The storage shelves should be made from 0.6 mm thk powder coated MS sheet which should be affixed below the desk top. Hooks should be provided on either sides of the vertical frame of the desk, for hanging bags/bottles. They should be made from 6.0 mm dia MS rods. The understructure should be assembled using M5 taptite screws. Level adjustors should be provided to take care of unevenness in floor. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Level2 & Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Teacher Table of Overall Size (in mm): 900W x 590D x 750H Top Worksurface should be made up of 18mm thk. PreLaminated Board (PLB). All work surface edges should be duly sealed with 2mm thick PVC beading. Understructure: Tubular Fame should be made up of MS ERW Square tube 25.4mm x 25.4mm x 1.2mm Thick. Modesty Panel should be made up of 1.0mm Thick CRCA MS Sheet. Should have One No. of storage unit on the right side fitted below worktop. Drawer Unit should be made up of Shell : 0.5mm Thick CRCA MS, Drawer Tray : 0.5mm Thick CRCA MS, Drawer Front : 0.8 Thick CRCA MS, Lock : 10 Lever Cam Lock & Handles : Built in Plastic. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make -GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Teacher Chair of Overall Size (in cm): 61.4W x 64.5D x 89.5H & 46.5SH SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam should be designed with contoured lumbar support for extra comfort. The seat should have an extra thick foam on front edge to give comfort to popliteal area. *BACK SIZE : 47.5 cm. (W) x 58.0cm. (H) *SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) POLYURETHANE FOAM: The Polyurethane foam should be moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 at 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME : The powder coated tubular frame should be cantilever type & made of dia 25.4mm x 2mm thk M.S. ER.W. Tube. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Level2 & Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Lab Stool with Back of Overall size (in cm): 65.0W x 65.0D x 66.0-77.5H & 45.0-56.5SH SEAT ASSEMBLY : Seat size - Dia 40.0cm, Adjustments - 360° Revolving type. BACK ASSEMBLY : Back size - 45.0 cm (W) covered with polyurethane foam. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45 ±2 Kg/m3 and Hardness load 16±2 kgf as per IS:7888 for 25% compression. HEIGHT ADJUSTMENT : The manual height adjustment should be very easy to operate with a help of a knob. It should be easily locked at the most comfortable position. PEDESTAL ASSEMBLY: The five-prong pedestal should be fabricated from 0.2±0.02 cm thick HR Sheet (IS: DD 1079 / HR), powder coated (DFT 40-60 microns) and fitted with an Injection moulded black Polyurethane Hub Cab and 5 nos. twin wheel castors. The pedestal should be 55.0±0.5cm pitch circle diameter (65.0±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors should be injection moulded in Black Nylon. These dimensions are product out to out dimensions & variations within ±1.0cm are normal. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Executive High Back Chair of Overall Size (in cm): 76.1W x 76.1D x 114.0-128.2H & 45.5-55.5 cm SEAT/BACK ASSEMBLY: The seat should be made up of 1.2±0.1 cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18. The Back should be made up of injection moulded glass filled nylon & upholstered using Mesh fabric with high tenacity yarn. *Seat Size: 47.0W x 49.5D cm *Back Size: 45.0W x 65.3H cm HIGH RESILIENCE (HR) POLYURETHANE FORM: The HR polyurethane seat foam should be moulded with density 45±2 kg/m? and hardness 16±2 kgf as per IS:7888 for 25% compression. ARMRESTS: The adjustable armrest should be designed with the following features - > Up-Down adjustemnt - 8 steps (8.0±0.5 cm range) > Height Adjustment armrest structure which should be Powder Coated & fitted with an armrest top. > Fixed Armrest Top should be PU moulded over metal insert. LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad should have an adjustment of 8.0±0.5 cm in height. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the following features - > 360° Revolving type. > Single point control. > Front-pivot for tilt with feet resting on ground ensuring more comfort. > Tilt tension adjustment. Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Physic/Chemistry Lab Island Table (Make - IKEA/HERMAN MILLER/GODREJ/HAWORTH) of Overall Size (in mm): 6000W x 1500D x 900H Understructure: C-frame assemblies from standard hollow section conforming to IS 7138/Latest size 60mm x 30mm x 2mm thick with CRC sheet of 18 x 20 gauge conforming to IS 513/Latest (±2) Top material: Prepolished granite finish of 18mm thk. Removable back panel, side cover panel, filler pankel: Made of CRCA MS 1mm thickness and coated with epoxy powder. Pulls on drawer/cabinet: anodized aluminum recessed-type. Sink Assembly: PP Drop-In Sink should be of size 560mm (W) X 355mm (D) Gas Valve: 2-Way LPG Valve Reagent Shelf: Fixed Type Reagent Shelf (Main/Add on Type) 1200 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only). 6/16A, 6 Pin Shutter Socket, 6 Module Plate & 16A, 1 Way Switch. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, SEFA & BIFMA Certifications) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Botany / Zoology Lab Island Table of Overall Size (in mm): 6000W x 1500D x 900H Understructure: C-frame assemblies from standard hollow section conforming to IS 7138/Latest size 60mm x 30mm x 2mm thick with CRC sheet of 18 x 20 gauge conforming to IS 513/Latest (±2) Top material: Prepolished granite finish of 18mm thk. Removable back panel, side cover panel, filler pankel: Made of CRCA MS 1mm thickness and coated with epoxy powder. Pulls on drawer/cabinet: anodized aluminum recessed-type. Sink Assembly: PP Drop-In Sink should be of size 560mm (W) X 355mm (D) Reagent Shelf: Fixed Type Reagent Shelf (Main/Add on Type) 1200 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only). 6/16A, 6 Pin Shutter Socket, 6 Module Plate & 16A, 1 Way Switch. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, SEFA & BIFMA Certifications) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Home Sci. / Environment Sci. Lab Island Table of Overall Size (in mm): 6000W x 1500D x 900H Understructure: C-frame assemblies from standard hollow section conforming to IS 7138/Latest size 60mm x 30mm x 2mm thick with CRC sheet of 18 x 20 gauge conforming to IS 513/Latest (±2) Top material: Prepolished granite finish of 18mm thk. Removable back panel, side cover panel, filler pankel: Made of CRCA MS 1mm thickness and coated with epoxy powder. Pulls on drawer/cabinet: anodized aluminum recessed-type. Sink Assembly: PP Drop-In Sink should be of size 560mm (W) X 355mm (D) (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, SEFA & BIFMA Certifications) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Steel Almirah of Overall Size (in mm): 1980H x 916W x 486D Construction & Material: Should be Welded Construction, 0.7mm thick (±0.07mm) CRCA (D Grade as per IS:513) for shelf, 0.8mm thick (±0.08mm) High yield strength (D Grade High yield Strength as per IS:513) CRCA for Doors & Back, 0.9mm thick (±0.08mm) CRCA (D Grade as per IS:513) for all other components. Locking & Handle - Should be Mazak Handle, Three way locking mechanism with shooting bolt. Shelving - Should be Height wise adjustable shelf mounting, Uniformly distributed load capacity per each full shelf is 40 Kg maximum, 4 Nos. adjustable full shelf Leveler - Should have M10 Screw type leveler with hex plastic base. Finish - Should have Epoxy powder coated to the thickness of 50 microns (±10) (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Executive Table for Principal of Overall Size (in mm): 2400W x 1560D x 750H Main Desk should be of size (in mm): 2400W x 1050D x 750H made from MDF+VENEER+PU Coating & should have Main Top Size (in mm): 2400W x 1050D & Top thickness 65mm made up of MDF+VENEER+PU Coating. Modesty of size (in mm): 2240W x 600D & thickness 16mm made up of MDF+VENEER+PU Coating. Mobile Pedestal of size (in mm): 510W x 445D x 635H made up of MDF+VENEER+PU Coating. ERU should be of size (in mm): 1200W x 445D x 660H made from MDF+VENEER+PU Coating & should have ERU Top size (in mm): 1200W x 445D & Top thickness 25mm. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Backunit for Principal of Overall Size (in mm): 2215W x 410D x 2000H Back Unit should be made from MDF+VENEER+PU Coating & Glass Doors. Glass should be of thickness 5mm. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Executive High Back Chair for Principal of Overall Size (in cm): 76.1W x 76.1D x 112.7-130.2H & 43.1-53.1SH SEAT ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m?, and hardness load 16±2 kgf as per IS:7888 for 25% compression. *Seat Size: 47.0W x 48.0D cm. BACK ASSEMBLY: The Cushioned back should be made of PU Foam with insitu molded MS ERW Round Tube of size 1.9±0.03cm x 0.16±0.0128cm. It should be upholstered with Leatherette. *Back Size: 47.7W x 76.4D cm. ARMRESTS: The armrest top should be moulded from polyurethane (PU) and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03 cm x 0.2±0.01 cm thk MS ERW tube having chrome plated finish. The armrest height adjustable up to 6.5±0.5 cm in 5 Steps. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the following features- > 360° Revolving type. > Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. > Tilt tension adjustment can be operated in seating position. > 5-position Tilt limiter giving option of variable tilt angle to the chair. > Seat/back tilting ratio of 1:2 > The mechanism housing made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Executive Visitor Chair for Principal Room of Overall Size (in cm): 60.9W x 64.2D x 98.2H & 44.8SH SEAT ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m?, and hardness load 16±2 kgf as per IS:7888 for 25% compression. *Seat Size: 47.0W x 48.0D cm. BACK ASSEMBLY: The Cushioned back should be made of PU Foam with insitu molded MS ERW Round Tube of size 1.9±0.03cm x 0.16±0.0128cm. It should be upholstered with Leatherette. *Back Size: 47.7W x 60.1D cm. VISITOR TUBULAR FRAME: The tubular frame should be cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk SS 202 tube. The back should be connected to frame through chrome plated high presure die cast connector piece. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Level2 & Green Guard Certificates) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Sofa Three Seater of Overall Size (in mm): 205.5W x 92D x 82H & SH 45cm. 1) SEAT FOAM: The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of PU foam with Density 28 ± 2 kg/cu.mtr. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu.mtr with two additonal top layer of supersoft foam of density 23 ± 2 kg/cu.mtr upholstered with fabric or leatherette. 3) UNDERSTRUCTURE: Understructure should be made up of 1.2 ± 0.1 cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-184 Dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose. 4) LEG ASSEMBLY: It should be a welded assembly made in stainless steel (grade SS 202) tube & plate. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Level2 & Green Guard Certificates) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Centre Table of Overall Size (in mm): 112W x 60D x 35.1H with Glass 12±0.3 mm thick black tinted Toughened Glass UV glued with bushes made in SS 202 grade for fixing with understructure. Understructure: Welded Assembly made in SS 202 grade having Dia. 12±0.04 as per IS:1762. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DORIAN/ZUARI/BETHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Storage Unit Sliding Door of Overall Size (in mm): 1200W x 450D x 1168H Sliding Door Unit should have Metal Door Center Partition with half shelves on each side made from Prime Quality CRCA Steel ? 0.8 mm Thick & Rigid Knock down construction. It should have Sliding Door with top hanging arrangement to prevent derailment. Each door provided with 2 Plastic roller having steel ball bearing for smooth movement of door & less noise. Should have Snap on type aesthetically appealing die cast 5 Lever Cam lock for safe locking and Plastic flush & recessed handle. Shelving : ? Height wise Adjustable Shelf Mounting ? Uniformly Distributed Load Capacity per each full shelf is 80 Kg maximum & for half shelf it is 40 Kg. ? 4 Nos. of Adjustable Half Shelves Should have Epoxy Polyester Powder coated of thickness of 50 microns (+/-10). (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Office Table of Overall Size (in mm): 1200W x 600D x 750H The Table should be made up of 18mm Prelam Particle Board, 3mm Prelam MDF Board. BM Slide for Keyboard, Castor Mounting Plate, Locking Bracket, Angle Clit should be made up of Metal. Construction should be KD fitting , Wooden Dowel & Angle Clit. Load bearing capicity should be for Table Top - 35Kgs, Shelf - 12.5Kgs & Drawer - 5.6Kgs (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Visitor Chair of Overall Size (in cm): 61.4W x 64.5D x 89.5H & 46.5SH SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam should be designed with contoured lumbar support for extra comfort. The seat should have an extra thick foam on front edge to give comfort to popliteal area. *BACK SIZE : 47.5 cm. (W) x 58.0cm. (H) *SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) POLYURETHANE FOAM: The Polyurethane foam should be moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 at 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME : The powder coated tubular frame should be cantilever type & made of dia 25.4mm x 2mm thk M.S. ER.W. Tube. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Level2 & Green Guard Certificates) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Canteen Table of Overall Size (in mm): 800W x 800D x 745H Table Top should be made from 1.2mm (±0.3mm) Thk SS-304 Brushed Steel finish sheet. Welded stiffener assemble should be made from 0.6mm Thick SS-304 glued with the top with special Glue. Understructure should be foldable & stackable, made of combination of Aluminium & Plastic. Centre column should be of Aluminium extrusion of Dia 70mm which should be anodized. Base should be made of 2 pieces of die case aluminium with buffed finish. It should be bolted together with centre column & top flange. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Canteen Chair of Overall Size (in cm): 52.5W x 55.8D x 84.5H & 45.0SH Seat/Back: The Seat and Back should be made up of injection moulded high impact Strenght Polypropylene polymer compound with indoor grade UV resistance *Seat Size: 52.5cm (W) x 53.2cm (D) *Back Size: 51.6cm (W) x 40.5cm (H) M.S. Powder Coated Understructure: The powder coated (DFT 50±10 microns) welded tubular frame made from Dia 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm M.S.E.R.W tube. Shoe: The shoes should be made of high impact strenght Polypropylene polymer compound with indoor grade UV resistance and pressed fitted with tubular frame. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Meeting Room Revolving Chair of Overall Size (in cm): 75.0W x 75.0D x 99.0H & 49.0SH SEAT/BACK ASSEMBLY: The Cushioned seat assembly should consists of seat outer (material-30% Glass Fiber Nylon) & upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric wth high tenacity yam. * Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) * Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45±2 kg/m3 and Hardness load 12 ±2 kgf as per IS:7888 for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished Aluminium. ARMRESTS : The armrest should have two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminium structure of armrest which should be connected to Aluminium Back spine and is operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the following features: ?360° revolving type ?Front-pivot for tilt with feet resting on ground & continious lumber support ensuring more comfort ?Tilt tension adjustment can be operated in seating position ?5 position Tilt limiter giving option of variable tilt angle to the chair ?Seat / back tilting ratio of 1:2 ?The mechanism housing should be made up of HPDC Aluminium & black powder Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Meeting Room Fixed Chair of Overall Size (in cm): 65.5W x 58.2D x 99.5H & 48.5SH SEAT/BACK ASSEMBLY: The Cushioned seat assembly should consists of seat outer (material-30% Glass Fiber Nylon) & upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric wth high tenacity yam. * Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) * Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45±2 kg/m3 and Hardness load 12 ±2 kgf as per IS:7888 for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished Aluminium. ARMRESTS : The armrest should have two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminium structure of armrest which should be connected to Aluminium Back spine and is operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner. LUMBAR SUPPORT ASSEMBLY: The Lumbar suport assembly should consists of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminium Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm TUBULAR FRAME: The powder coated (DFT 40-60 micron) tubular frame should be cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing D. Controller Table of Overall Size (in mm): 1500W x 600D x 750H Worktop should be made of 25mm Thick Pre-laminated board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap should be provided on work surface for wire management. Modesty Panel should be made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Cube legs should be fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) should be welded for fixing worktop. These should be welded together by argo shield welding. This welded structure should be coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert should be fixed, on to which a straight M8 leveler fitted which allows for adjustment of the height upto 50mm. Cross Members should be made from 50mm X 25mm X 1.2mm thick ERW tube (as per IS:7138). These should be coated with 50 micron epoxy polyester coating. Cross Members should be assembled by friction fit PDC joinery and grub screws. There should be always two cross members for one table. Soft closing access flap should be used in Desk. Provision for standard size of 8 module electrical (Anchor Roma) should be offered. Access flap should be made from Aluminum extrusion, PDC parts made from Aluminum Alloy and plastic parts should be made from Nylon 6 and wire brush with nylon bristles. Power box should be made with 0.8 mm thick CRCA (IS: 513), with switch plate (8 Module cutout provision for Anchor Roma). This should be fixed with worktop along the depth at Access Flap position. It should have an Add-on Storage (3Drawers Free Standing Pedestal) of size (in mm): 640H x 390W x 440D. (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Item Description Providing & Placing Teacher Meeting Table of Overall Size (in mm): 3600W x 1500D x 740H Work top should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access panels provided with soft closing hinges. The Understructure should consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile should be added at bottom edges for improving the aesthetics. The product should have a knockdown construction. Wire Management: Bottom cabinet with door should be provided for flow of wires and cables. Cutout provision below Access flap at four locations for standard 8 module Anchor Roma should be provided. Beside each cutout, an additional cutout with plate should be provided for mounting Audio Visual Cables (eg. HDMI,VGA-A,etc). (The manufacturer should have ISO 9001, ISO 14001, ISO 18001, ISO 45001, ISO 50001, BIFMA Green Guard Certificates) (Make - GODREJ/DURIAN/ZUARI/METHODEX) Estimated Cost (Inclusive of GST) |
Sum(Estimated Cost (Inclusive of GST)): () |