Item Description Providing & Fixing chicken wire mesh of 22 gauge in junction of RCC and Brick work walls for internal Works fixed with U nails @ 150 mm c/c including scaffolding etc complete as per direction of Engineer-in-charge. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing glass reinforced concrete (GRC) customized jali 50mm thick on Aluminium Frame work (Tubular section of size as required). Approximate size of Jali 1100 mm x 1800mm). Basic Rate of jali 4200 Rs./SqM excluding taxes, freight and loading & unloading Estimated Cost (Inclusive of GST) |
Item Description Dismantling of building/ structures in entirety up to the ground level manually or with power machinery as approved by Engineer-in- charge including provision of necessary tools, tackle, plant scaffolding etc,following all safety requirements, ensuring adequate precaution to the neighborhood structures & equipment, putting necessary cover, removing debris outside station limit as directed by Engineer in charge all complete for making the site level,clear and tidy for construction of new building/structure etc. The rates shall be inclusive of rebate for servicable material. Note:-1. Buy back of all dismentling building materials of the existing building. The contractor shall be deemed to have full knowledge of the building being dismantled, which may be obtained from site inspection before submission of offer. 2. The work shall in general be done according to Latest CPWD specification. 3. Dismantling shall be allowed during day shift only & proper permission for the same shall be obtained. 4. Providing of necessary covers/barricades around the work area is to be done prior to dismantling operations. 5. The building shall be demolished stage by stage manually or with power machinery. Use of explosives or Dynamite shall not be allowed. 6. The unserviceable materials and rubbish shall be removed immediately during the course of demolition and disposed off as per Green Building norms at no extra cost .All required permissions & clearances shall be arranged by the Contractor. Dismantling of existing Building Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing white vitreous china wash basin under counter basin, with C.I. concealed type brackets fixed to walls with GI rag bolts or approved fasteners etc., including 32 mm CP brass waste coupling, including painting of fittings and brackets, cutting and making good the walls wherever required all complete (Granite counter top will be measured and paid separately under relevent item): as per approved make and decision of engineer-in-charge Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing CP brass auto closing system basin pillar tap of Jaquar PRS - 001 or Equivalent as approved by Engineer- In Charge Estimated Cost (Inclusive of GST) |
Item Description Providing & fixing in position GI 100x50 elbow floor drain including cost of cutting and making good the walls and floors wherever required. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing S.S grating of approved quality and colour. Circular type 125 mm nominal dia. as per direction of the engineer in charge . Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing CP liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms all complete job as per direction of the engineer in charge . Estimated Cost (Inclusive of GST) |
Item Description Providing & Fixing water purifier cum water cooler made of stainless steel having storage capacity of 40 liter & cooling capacity 40 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge . Estimated Cost (Inclusive of GST) |
Item Description Supplying, storing, handling, shifting, installation, testing and commissioning of CP flxible hose, spray, wall flange of Make- Jaquar/ Cera/ Kohler/Marc or equivalent as per direction of the engineer in charge with all fittings and fixtures all complete job as per direction of the engineer in charge . Estimated Cost (Inclusive of GST) |
Item Description Providing, fitting & fixing of CP Bib Cock two in one Make- Jaquar/ Cera/ Kohler/Marc or equivalent as per direction of the engineer in charge all complete job as per direction of the engineer in charge . Estimated Cost (Inclusive of GST) |
Item Description Supply, installation, testing and commissioning of package type floor mounted RO plant complete with pre-treatment system comprising of feed water pump (1W+1S), MGF, ACF, dosing systems, RO membrances, RO high pressure pump (1W+1S), post treatment system comprising of dosing system; Antiscalent dosing system, UV Dose. The unit shall have all interlocking for safe operation of plant. The unit shall have MS skid mounted electrical panel complete with required starters and shall also have all Annuanciation and Controls. Indication instrumentation such as TDS meter at inlet/outlet, flow meter & totalizer, Pressure switches shall also be provided. The piping shall be HDPE for High Pressure Line. The filter shall be FRP and pumps shall be of SS construction. The basis of design shall be for feed water inlet TDS of 2000 PPM. Contractor is suggested to cary out the feed water chemical analysis and ensure suitability of RO plant operation. Make: BS Enviro/Thermax/Ion Exchange or equivalent as per direction of engineer incharge. (a) For 2000 LPH RO as described above. Estimated Cost (Inclusive of GST) |
Item Description Supply , Installation , Testing and Commissioning of Stainless Steel Water Storage Tank Grade SS -316 of 5000 liters capacity with 0.6mm thick , Fabrication of Inlet , outlet , overflow , drain , base etc . Stainless Tank Water Storage Tank shall be FDA Listed and NSF approved . Stainless Steel Water Storage Tank shall be Pressurized type and thickness of tank shall be 4 mm thick . Stainless Steel Water Storage Tank shall be duly insulated with 50 mm thick fibre glass wool insulation and 24 Gauge aluminium Cladding . Estimated Cost (Inclusive of GST) |
Item Description AIR COOLED HEAT PUMP FOR GENERATING HOT WATER: Supply , installation , testing & commissioning of Micro Processor Controlled aircooled reversible scroll Heat pump delivering actual capacity as per the following parameters duly installed at site. The chiller should be complete with single/multiple hermatic scroll compressors , Four way reversing valve, Electronic Expansion Valve, defrosting cycle, Liquid reciever, Copper tube/ aluminum fins air cooled heat exchanger with Axial fans with IP54 protection, braze plate type( SS316) primary heat exchanger, anitvibration rubber mounts with factory assembled with required fittings, valves, piping, Electrical panel mounted on the chiller including the disconnect switch suitable for 50 Hz, 3 phase 415 volts,ac supply. The vibration isolators should be shipped alongwith chillers. Heat Pump should be capable of generating Hot Water upto 65ºC. The heatpump should be capable for operation from -10 Deg C to 47 Deg C .Refrigerant circuit to include liquid injection of refrigerant for higher temperature application liquid line solenoid valve, drier filter with replaceable solid cartridge, liquid line sight glass, electronic thermostatic valve, high pressure safety valve, high & lower pressure transducers, high and low pressure switches, liquid receiver etc. The heat pump should be suitable for operation on Environment friendly refrigerant R407c/ R410a and should come factory charged with refrigerant. Heating capacity = 50 kW Actual at below mentioned conditions, Hot water inlet temp.= 15 Deg C, Hot water outlet temp.= 65 Deg C, Design ambient temp. = 7 Deg C, Refrigerant : R-407C, COP ( Actual) : Min 2.9 ( with Fans), Optional : RS-485 serial card for Modbus BMS ( 2W : 1SB ). Estimated Cost (Inclusive of GST) |
Item Description Supply, installation, testing & commissioning of Solar Water Heating System of 35 NOS ISI Marked Solar Flat Plate Collectors of size 2080mm X 1070mm X 100mm, Laser welded . with necessary Stands, Support etc. with 3500 Ltrs capacity SS -304 hot water storage tank of thickness 4 mm duly insulated with 50 mm thick PUFF insulation & 24 SWG Aluminium Cladding, with Heat Exchanger of suitable surface area, with necessary makeup tank, with suitable Electrical backup for cloudy / foggy days, with necessary piping with solar panels & solar hot water tank, with one No. temperature Gauge, with 01 Nos. Ball valves, to produced hot water up to 60 degree C on clear sunny days. (MNRE Approved) Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SCH-40 pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (a) 65 mm nominal outer dia Pipes Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SCH-40 pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (b) 80 mm nominal outer dia Pipes Estimated Cost (Inclusive of GST) |
Item Description Supply ,Erection , Testing & Commissioning of Automatic water level control panel & related accessories for pumping automation with consisting of automatic water level controller , level sensor with stainless steel probe, motorized butterfly valve, motorized valve controller with complete in all respect. (a) upto 50 mm dia. nominal bore Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing HDPE Pop Up Sprinkler Irrigation System Pop height 100 mm with fittings all complete as per direction of engineer in charge. Estimated Cost (Inclusive of GST) |
Item Description Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098 ( Part - 2 ) 3013 for soil / waste pipe under ground drainage system with jointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. (a) 150 mm diameter Estimated Cost (Inclusive of GST) |
Item Description Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098 ( Part - 2 ) 3013 for soil / waste pipe under ground drainage system with jointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. (b) 200 mm diameter Estimated Cost (Inclusive of GST) |
Item Description Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098 ( Part - 2 ) 3013 for soil / waste pipe under ground drainage system with jointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. (c) 250 mm diameter Estimated Cost (Inclusive of GST) |
Item Description Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098 ( Part - 2 ) 3013 for soil / waste pipe under ground drainage system with jointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. (d) 300 mm diameter Estimated Cost (Inclusive of GST) |
Item Description Supply, installation, testing & commissioning of variable speed hydropneumatic system mounted on a common base plate comprising of vertical inline multistage pumping set with Stainless steel-304 body, Stainless steel-304 impeller, Stainless steel-304 casing, shaft of Stainless steel-316 and C.I. base & head with mechanical seal, shaft directly coupled to a TEFC induction motor with class IE -3 efficiency and IP 55 Protection and class F insulation suitable for 400/440 volts, 3 phase, 50 cycles AC supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundation, one No. microprocessor based controller, two Nos. variable frequency drives, one No.remote sensors, transmitters, sequence running cotroller, dry running Protection,motor control centre, necessary power and control cabling from MCC to pumps including required rating of MCB, two Nos. required capacity M.S diaphragam tank with interchangeable butyl rubber membrane,complete in all respects including suction and delivery headers of G.I "C" class pipe of required dia, isolation valves, NRV of PN-16 grade & vibration eliminators on both suction & delivery side of pumps, power box, equipped with fuses/ isolators/circuit breakers as required. No. and capacity of Pressure Vessel - 01 Nos. x 200 litres min. (Or as per Manufacturer Calculations) The system shall also comprise the following:- Control Panel with Programmable Logic Controller (PLC) with in-built PID controller with 16 inputs and 12 outputs, digital display with fluorescent screen with 2 lines of 20 character each equipped with 8 function keys and 9 service keys, 3 Phase, 415 V I/P, 4 KW, AC variable speed drive with in-built EN55011 Class A RFI Filters, having standard function of BI Loop , energy saving, catching a spinning load with speed search, auto hunting jog, preset speeds, controlled stop on loss of supply power loss side through, D.C. injection braking, fast stop. Drive should have selectable, rated input frequency 50/60 Hz and output frequency range of 0.5-32 HZ, contractors, overlead relays and MCBs should confirm to IEC-898-1995 standards Ammeter, voltmeter. All strip indication should blink in case of trip and panel should only be accessible through an access code. Type 8202 pressure transducer with SS pressure sensor and control electronic board. Output 4-20m A on two wires conforming BS-6134 standards and IP 55 protection class. Domestic Water Transfer Pump (at existing pump room for science block) Set of Two pumps (1 Working + 1 Standby) Capacity - 275 LPM, Head - 60.0 Mtr., Eff. - Class IE-3 Estimated Cost (Inclusive of GST) |
Item Description Flushing Water Transfer Pump ( at existing pump room for science block ) Set of Two pumps (1 Working + 1 Standby), Capacity - 180LPM, Head - 60.0 Mtr. Eff. - Class IE-3 Estimated Cost (Inclusive of GST) |
Item Description Supply, installation testing & commissioning of borewell submersible pumping set suitable to operate on 415 volts 3 phase 50 HZ A.C. power supply including water proof joint free cable, motor control panel, 200 mm outer dia uPVC Pipe as per IS : 12818 with fittings, clamps etc. complete in all respect as per details given below :- 275 LPM, Head - 60.0 Mtr., Eff. - Class IE-3 Pump Motor shall be Class F Insulation , Pump and Motor shall be IP : 68 Protection Rating , and Motor Efficiency shall be Class IE-3 Efficiency . Pump to be lowered below ground at : 90 M Pump capacity : 15000 litres/hr Head : 120 M H.P: 12 ( Approx)Total of one set Tubewell Estimated Cost (Inclusive of GST) |
Item Description Supply, installation & testing and commissioning of vertical floor mounted filter of suitable size, provided with an inlet distributor. The vessel material of M.S with FRP lining / epoxy coating with G.I. frontal piping ,inter connection, suction & delivery header and valves (C.I.) , back wash system & filter media etc. complete with standard fittings like access cover, pressure gauge at inlet & outlet, sampling cock, rinse drain valve, air vent valve with piping, bolts, nuts & rubber gaskets.Multi Grade Filter ,Capacity/Flow rate : 20 M3/hr,Operating pressure : 3.5 kg/Sq.cm ,Test pressure : 5.5 kg/Sq.cm ,MOC - M.S DIA - 1400 MM , HOS - 1500 MM Estimated Cost (Inclusive of GST) |
Item Description Activated Carbon Filter, Capacity/Flow rate : 20 M3/hr,Operating pressure : 3.5 kg/Sq.cm ,Test pressure : 5.5 kg/Sq.cm ,MOC - MS,DIA - 1400 MM , HOS - 1500 MM Estimated Cost (Inclusive of GST) |
Item Description Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel-304 body, Stainless steel-304 impeller, Stainless steel-304 casing, shaft of Stainless steel-316 and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock,including suction and delivery headers of G.I "C" class pipe of required dia, isolation valves, NRV of PN-16 grade,required valve and strainer & vibration eliminators on both suction & delivery side of pumps, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information.,Filter Feed Pump (1 working + 1 standby),Flow rate (each) = 20 m3/hr ,Head = 30 - 35 m Estimated Cost (Inclusive of GST) |
Item Description Supply, installation & testing and commissioning of MBBR STP complete with design and dawing , standard fittings like access cover, pressure gauge at inlet & outlet, sampling cock, rinse drain valve, air vent valve with piping, Butterfly valve , NRV bolts,Sensor , nuts & rubber gaskets. With below equipment all complete works as per Engineer-in-Incharge.,Submersible Sewage Feed pump (1W:1SB ) 02 Nos , Flow rate -20 -25 m3 / hr , Screen Bar S/S 304 - 2 Nos , Head - 8-10 mtr ,as suitable size Air Blower ? 02 nos - 150 cum/h (Approx ) Diffusers MBBR Media in lot Chlorine Dosing System Filter Feed Pump ?(01W+01SB) 02 Nos , Flow rate -25 m3 / hr , Head 8-10 mtr FRP Sand Filter-Filter dia approx. -1400 mm FRP Carbon Filter - Filter dia approx. -1400 mm All Interconnecting pipe Work G.I/ HDPE /MS , Apoxy Paint. Filter press 12? X 12? Screw pump (01W+01S) - - 5 m3 / hr Electrical Panel Recycling Feed pump Anoxic Tank with with Sub. Mixer , UV ,UF ,Ozonator etc.,275 KLD ( MBBR STP ) Estimated Cost (Inclusive of GST) |
Item Description Control Panel with Programmable Logic Controller (PLC) with in-built PID controller with 16 inputs and 12 outputs, digital display with fluorescent screen with 2 lines of 20 character each equipped with 8 function keys and 9 service keys, 3 Phase, 415 V I/P, 4 KW, AC variable speed drive with in-built EN55011 Class A RFI Filters, having standard function of BI Loop , energy saving, catching a spinning load with speed search, auto hunting jog, preset speeds, controlled stop on loss of supply power loss side through, D.C. injection braking, fast stop. Drive should have selectable, rated input frequency 50/60 Hz and output frequency range of 0.5-32 HZ, contractors, overlead relays and MCBs should confirm to IEC-898-1995 standards Ammeter, voltmeter. All strip indication should blink in case of trip and panel should only be accessible through an access code.,Type 8202 pressure transducer with SS pressure sensor and control electronic board. Output 4-20m A on two wires conforming BS-6134 standards and IP 55 protection class.,Domestic Water Transfer Pump ( Hostel Area Proposed UGT ) ,Set of three pumps (2 Working + 1 Standby),Capacity - 400 LPM,Head - 60.0 Mtr.,Eff. - Class IE-3 Estimated Cost (Inclusive of GST) |
Item Description Flushing Water Transfer Pump ( Hostel Area Proposed UGT ) Set of three pumps (2 Working + 1 Standby),Capacity - 200 LPM,Head - 60.0 Mtr.,Eff. - Class IE-3 Estimated Cost (Inclusive of GST) |
Item Description Domestic Water Transfer Pump (at hostel terrace ) Set of Two pumps (1 Working + 1 Standby),Capacity - 150 LPM,Head - 30.0 Mtr.,Eff. - Class IE-3 Estimated Cost (Inclusive of GST) |
Item Description Supply, installing, testing and commissining of submersible single stage single entry pumps with SS -304 Casing / Body , SS -304 Impeller , SS -316 Shaft connected to TEFC submersible motor with class IE-3 efficiency and IP 55 Protection and class F insulation for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphram and bend, vertical discharge pipe, guide pipe and chain in built level controller, sequence running controller, dry running Protection with gunmetal isolation cock,including suction and delivery headers of G.I "C" class pipe of required dia, isolation valves, NRV of PN-16 grade,required valve and strainer & vibration eliminators on both suction & delivery side of pumps complete in all respects. ,(Pumps shall be installed in a set of two pumps One working and One standby , Pump shall be automatic ON / OFF on Cyclic Pattern ) ,Drainage Sump Pumps ( 1 Working : 1 Standby ),(Pumps to be suitable to handle solids upto 28 mm size) ,Capacity - 250 LPM (Each),Head - 15 M,Eff - Class IE-3 Estimated Cost (Inclusive of GST) |
Item Description Providing & fixing double flanged flexicon rubber expansion joint with unit control of standard length as per maufacturers specs. Tested to a pressure of 20 Kg/Sqcm including rubber gaskets, flanges, nuts, bolts and washers complete as required. 80 mm dia Estimated Cost (Inclusive of GST) |
Item Description Providing & fixing double flanged flexicon rubber expansion joint with unit control of standard length as per maufacturers specs. Tested to a pressure of 20 Kg/Sqcm including rubber gaskets, flanges, nuts, bolts and washers complete as required. 150 mm dia Estimated Cost (Inclusive of GST) |
Item Description Providing & fixing double flanged flexicon rubber expansion joint with unit control of standard length as per maufacturers specs. Tested to a pressure of 20 Kg/Sqcm including rubber gaskets, flanges, nuts, bolts and washers complete as required. 200 mm dia Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing Fire Extinguishers (CO2 type powder ) 22.5 Kg Capacity ( heel type ) complete with all accessories as per manufacturers specifications. ( Pump room ) Estimated Cost (Inclusive of GST) |
Item Description Providing & fixing GM fire Brigade Suction hose coupling (Draw out Connection) with nut for female coupling as per IS:902-1974 complete with 100mm dia. 1 No C.I Foot valve flanged (to be connected to static water tank) Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing dial type pressure gauge with isolation cock and copper pipe on main header Dial diameter 100 mm celebration 0-16 / sq. cm. Estimated Cost (Inclusive of GST) |
Item Description Supply, installation and fixing of MS Axe of approved by St.John Ambulance Brigade /Indian Red Cross society or equivalent as per direction of engineer incharge conforming to IS : 2217 - 1963 all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Doors and frame Supply, installation and fixing of MS door frame 1200x2100 door capable of accommodating fire hose reel, landing valve, hose pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) Cost of fire extinguishers not included in item rate. (Liasioing with civil contractor for making 1200x600x2100 Recessed type mansoary box all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Providing, storing, handling, shifting, installation, testing and commissioning of portable fire Extinguishers as described below: 4 kg carbon dioxide extinguisher, IS marked, with high pressure discharge tube, horn, control valve, CCE approved cylinder of Make :- ABC/Eco or equivalent as per direction of engineer incharge Fire all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Providing, storing, handling, shifting, installation, testing and commissioning of portable fire Extinguishers as described below: 6 kg carbon dioxide extinguisher, IS marked, with high pressure discharge tube, horn, control valve, CCE approved cylinder of Make :- ABC/Eco or equivalent as per direction of engineer incharge Fire all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Supply, installation and fixing of Shock treatment chart duly mounted on a wooden frame with glass on, as required in 2 languages (Hindi & English) all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Supply, installation and fixing weather proof of M.S. fire hose cabinet (750x600x250mm) made out of 16 gauge M.S. sheet capable of accommodating landing valve, hose pipes, fittings & accessories. The box shall have a front glass door with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) - for external and roof hydrant all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) Group C Estimated Cost (Inclusive of GST) |
Item Description Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) Primary point controlled by one MCB. Estimated Cost (Inclusive of GST) |
Item Description Same as item above but Secondary point. i.e. Points to be looped with Primary point with 2.5 sqmm wire and Point wiring Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing and Commissioning of 10W Surface mounted LED Bracket (Make-Bajaj Lighting or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, testing and commissioning of 5W LED mirror light shall be 6500K. equivalent as specified in the approved list of make.) Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing and Commissioning of 65W Surface mounted LED circular Downlighter (Make-Bajaj Lighting or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description MAIN LT PANEL-MDB PANEL GIRLS HOSTEL-Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 55 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks with sleeved TPN Aluminum Bus bars and GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade (RAL 7032) over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. This main panel must be extendable for future requirement in such a manner not to disrupt ongoing services at the point of use during extension. All LT Panel shall conform to latest IS/IEC -61439 code. All Panel shall be complete with power & control wiring, danger & inscription plate, Lifting hooks etc. Each incoming / outgoing breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. All the MCCB with adustable overload, short circuit & earth fault protection and above shall have microprocessor. The panel shall be manufactured as per BOQ, tech specification and drawing. (Note:The contractor may select the next higher fault rating of ACB/ MCCB if it is not readily available ,without any extra cost ,as the figure indicated within the bracket are required maxmum fault level of the panel.) NOTE: PANEL MUST BE AS PER IEC 61439 TYPE TESTED FROM ANY INDIA BASED TEST LABORATORY (CPRI/ERDA ETC) FOR ROTECTION AGAINST SHORT CIRCUIT/TEMPERATURE RISE/INTERNAL ARC/DEGREE OF PROTECTION) (PTTA PANEL UPTO 630A & TTA PANEL ABOVE 630A) Estimated Cost (Inclusive of GST) |
Item Description MAIN LT PANEL-MDB UPS PANEL-Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 55 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks with sleeved TPN Aluminum Bus bars and GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade (RAL 7032) over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. This main panel must be extendable for future requirement in such a manner not to disrupt ongoing services at the point of use during extension. All LT Panel shall conform to latest IS/IEC -61439 code. All Panel shall be complete with power & control wiring, danger & inscription plate, Lifting hooks etc. Each incoming / outgoing breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. All the MCCB with adustable overload, short circuit & earth fault protection and above shall have microprocessor. The panel shall be manufactured as per BOQ, tech specification and drawing. (Note:The contractor may select the next higher fault rating of ACB/ MCCB if it is not readily available ,without any extra cost ,as the figure indicated within the bracket are required maxmum fault level of the panel.) NOTE: PANEL MUST BE AS PER IEC 61439 TYPE TESTED FROM ANY INDIA BASED TEST LABORATORY (CPRI/ERDA ETC) FOR ROTECTION AGAINST SHORT CIRCUIT/TEMPERATURE RISE/INTERNAL ARC/DEGREE OF PROTECTION) (PTTA PANEL UPTO 630A & TTA PANEL ABOVE 630A) Estimated Cost (Inclusive of GST) |
Item Description MAIN LT PANEL-LIFT PANEL-Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 55 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks with sleeved TPN Aluminum Bus bars and GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade (RAL 7032) over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. This main panel must be extendable for future requirement in such a manner not to disrupt ongoing services at the point of use during extension. All LT Panel shall conform to latest IS/IEC -61439 code. All Panel shall be complete with power & control wiring, danger & inscription plate, Lifting hooks etc. Each incoming / outgoing breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. All the MCCB with adustable overload, short circuit & earth fault protection and above shall have microprocessor. The panel shall be manufactured as per BOQ, tech specification and drawing. (Note:The contractor may select the next higher fault rating of ACB/ MCCB if it is not readily available ,without any extra cost ,as the figure indicated within the bracket are required maxmum fault level of the panel.) NOTE: PANEL MUST BE AS PER IEC 61439 TYPE TESTED FROM ANY INDIA BASED TEST LABORATORY (CPRI/ERDA ETC) FOR ROTECTION AGAINST SHORT CIRCUIT/TEMPERATURE RISE/INTERNAL ARC/DEGREE OF PROTECTION) (PTTA PANEL UPTO 630A & TTA PANEL ABOVE 630A) Estimated Cost (Inclusive of GST) |
Item Description MAIN LT PANEL-VTPN BD PANEL-Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 55 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks with sleeved TPN Aluminum Bus bars and GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade (RAL 7032) over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. This main panel must be extendable for future requirement in such a manner not to disrupt ongoing services at the point of use during extension. All LT Panel shall conform to latest IS/IEC -61439 code. All Panel shall be complete with power & control wiring, danger & inscription plate, Lifting hooks etc. Each incoming / outgoing breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. All the MCCB with adustable overload, short circuit & earth fault protection and above shall have microprocessor. The panel shall be manufactured as per BOQ, tech specification and drawing. (Note:The contractor may select the next higher fault rating of ACB/ MCCB if it is not readily available ,without any extra cost ,as the figure indicated within the bracket are required maxmum fault level of the panel.) NOTE: PANEL MUST BE AS PER IEC 61439 TYPE TESTED FROM ANY INDIA BASED TEST LABORATORY (CPRI/ERDA ETC) FOR ROTECTION AGAINST SHORT CIRCUIT/TEMPERATURE RISE/INTERNAL ARC/DEGREE OF PROTECTION) (PTTA PANEL UPTO 630A & TTA PANEL ABOVE 630A) Estimated Cost (Inclusive of GST) |
Item Description 5 KVA UPS 1 phase (240 V + 15%) Volts input & 1 phase output (240 V + 1%), 50 Hz, IGBT based technology, Input harmonic Current THD <=3% typical at 100% load, ,<=6% maximum at 100% load with inbuilt Isolation Transformer and 30 min battery backup for each UPS along with battery cabinet, Parallel card, BMS Port & communication card complete in all respect including supporting steel structure for UPS and Battery as required.Quoted price shall be inclusive of required rating single core copper conductor cable including terminations,connections of UPS to batteries etc complete in all respect and as per direction of Engineer in Charge. Estimated Cost (Inclusive of GST) |
Item Description Supply of Lightnig counter - LCD screen shows the number of lightning strikes, hour and date of lightning events Buttons enable TIME/DATE setting and log viewing. Replaceable battery, working life minimum five years, meet the requirements for IS/IEC 62305 and IEC 62561-2.Tested for Electrical ,Mechanical and Chemical as per IEC 62561. Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 2C x 10 sq.mm. (19mm) Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 4 X 10 sq. mm. (28mm) Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 4 X 16 sq. mm. (28mm) Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3.5C x 25 sq.mm. (28mm) Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3.5C x 35 sq.mm. (32mm) Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3.5C x 50 sq.mm. (35mm) Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3.5C x 70 sq.mm. (38mm) Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3.5C x 150 sq.mm. (50mm) Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Trays-Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required..150 mm width X 50 mm depth X 1.6 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Trays-Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Trays-Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 450 mm width X 62.5 mm depth X 2.0 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Tray Bends- Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray bends with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Tray Bends- Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray bends with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Tray Bends- Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray bends with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 450 mm width X 62.5 mm depth X 2.0 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Tray Tee's- Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray tee's with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Tray Tee's- Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray tee's with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Tray Tee's- Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray tee's with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 450 mm width X 62.5 mm depth X 2.0 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Tray Cross Members- Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray cross members with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Tray Cross Members- Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray cross members with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness Estimated Cost (Inclusive of GST) |
Item Description S/ F powder coated of approved shade MS Cable Tray Cross Members- Supplying and installing following size of perforated powder coated of approved shade M.S. cable tray cross members with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 450 mm width X 62.5 mm depth X 2.0 mm thickness Estimated Cost (Inclusive of GST) |
Item Description Supplying & installing UTP networking Cat-6 cable suitable for LAN/WAN computer net working as per technical specifications all complete job as per direction of E/I. (Make:Digisol / D-Link/Cisco or equivalent as per direction of engineer in charge) Estimated Cost (Inclusive of GST) |
Item Description Supplying,Installing,Testing with Dome Camera Form factor 2 Megapixel high resolution Usage Indoor Usage Lens 1/3" angle of view: Day /night IR as per technical specifications including carriage and necessary required equipment all complete job as per direction of E/I Make Secure eye, Hikvision, CP Plus or equivalent as per direction of engineer in charge. Estimated Cost (Inclusive of GST) |
Item Description Supplying,Installing,Testing with bullet Camera Form factor 2 Megapixel high resolution Usage Indoor Usage Lens 1/3" angle of view: Day /night IR as per technical specifications including carriage and necessary required equipment all complete job as per direction of E/I. Make Secure eye, Hikvision, CP Plus or equivalent as per direction of engineer incharge. Estimated Cost (Inclusive of GST) |
Item Description Supplying,Installing,Testing of All-in-one Video Network recording solution (NVR) for up to 16 channels, Pre-installed, pre-configured IP storage solution with 8 TB storage capacity, RAID-5 protected,Hot-swappable hard drives, Temperature +10 °C to +35 °C, Relative humidity-8 to 90% (non-condensing), Recording shall be calculated for all cameras at full frame rate & resolution for 15 days as per technical specifications all complete job as per direction of E/I Make- Secure eye/Hikvision//CP Plus or equivalent as per direction of engineer incharge. Estimated Cost (Inclusive of GST) |
Item Description Supplying,Installing,Testing Hard Disk with Storage Capacity - 6 TB, HDD Type -Surveillance, Make- Seagate, WD, samsung or equivalent as per direction of the engineer in charge. Estimated Cost (Inclusive of GST) |
Item Description Supplying,Installing,Testing of Networking Poe Switch, 10/100/1000 BT ports, 8 ports providing PoE as per 802.3a/f as per technical specifications all complete job as per direction of E/I (Make- D-Link / Cisco/ Panasonic or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Supplying, Installing, Testing & Commissioning of Desktop Computer with Intel core 8th Generation Intel® Core? i7 processor, 8 GB RAM, 2 TB HDD storage, (WIFI/BT), 256 GB SSD storage USB Keyboard, USB Mouse, Preofessional Win10, 18.5?TFT having 3 Years Onsite warranty as per technical specifications including carriage and necessary required equipment all complete job as per direction of E/I (Make-DELL/ACER/LENOVO/HP or equivalent as per direction of the engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Supplying,Installing,Testing Display Panel with Screen Size- 32-inch Aspect Ratio- 16:9 Panel Backlight -IPS/Direct-LED Backlight Scanning -100Hz Resolution -1920 X 1080 pixels Viewing Angle-178 X 178 VIDEO IN -RCA X 1 AUDIO IN (L/R)/PC AUDIO IN -RCA Pin Type X 2 HDMI IN- TYPE A Connectors X 2 COMPONENT IN- Y, PB/CB, PR/CRX1 USB Input -USB 2.0 X 1as per technical specifications including carriage and necessary required equipment all complete job as per direction of E/I (Make:- Samsung/Sony/LG/Panasonic or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description HDMI to HDMI cable of 3 meter length as per technical specifications including carriage and necessary required equipment all complete job as per direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supllying,Installing,Testing and Commisioning of 6U Rack as per technical specifications including carriage and necessary required equipment all complete job as per direction of E/I. Make: VALRACK/D-LINK/Net Rack or equivalent as per direction of engineer incharge. Estimated Cost (Inclusive of GST) |
Item Description Supply , Installtion , Testing and comissioning of 42 port loaded LIU with adaptor plates , pigtel cables for connections. Estimated Cost (Inclusive of GST) |
Item Description Supply , Installtion , Testing and comissioning of LC-LC singlemode fiber patch cord. Estimated Cost (Inclusive of GST) |
Item Description Supply , Installtion , Testing and comissioning of loaded 24 port CAT6 jack panel for CAT6 cable termination. Estimated Cost (Inclusive of GST) |
Item Description Supply , Installtion , Testing and comissioning of CAT6 patch cord 7 feet for user termination to information outlet Rack End. Estimated Cost (Inclusive of GST) |
Item Description Supplying & installing UTP networking Cat-6 cable suitable for LAN/WAN computer net working as per technical specifications all complete job as per direction of E/I. (Make:Digisol / D-Link/Cisco or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Supplying,Installing,Testing of 6 Core Optical Fibre cable in prelaid PVC conduits / pipes / raceway all complete job as per direction of E/I. (Make: Finolex/havells or equivalent as per direction of the engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Supplying,Installing,Testing of 3x3 I/O box with face place Female Rf45 as per technical specifications all complete job as per direction of E/I. (Make:Digisol / D-Link/Cisco or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Supplying,Installing,Testing of CAT 6 Giga Speed 1.2 m Patch Cord as per technical specifications all complete job as per direction of E/I. (Make:Digisol / D-Link/Cisco) Estimated Cost (Inclusive of GST) |
Item Description Supply, installation, testing and commissioning of 12 U Networking Rack with Glassdoor all complete job as per direction of E/I (Make:- MATRIX/Dlink./Panasonic or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Supplying,Installing,Testing of 1 G SFP Module as per technical specifications all complete job as per direction of E/I. (Make- D-Link / Cisco/ Panasonic or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications. 02 loop Estimated Cost (Inclusive of GST) |
Item Description Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required. Estimated Cost (Inclusive of GST) |
Item Description Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. Estimated Cost (Inclusive of GST) |
Item Description Supplying, installation, testing & commissioning of addressable manual call point complete as required. Estimated Cost (Inclusive of GST) |
Item Description Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required. Estimated Cost (Inclusive of GST) |
Item Description Supplying, installation, testing & commissioning of fire fighter phone jack complete as required. Estimated Cost (Inclusive of GST) |
Item Description Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. Estimated Cost (Inclusive of GST) |
Item Description Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25mm Estimated Cost (Inclusive of GST) |
Item Description Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface/recessed PVC conduit as required. 10 Pair Cable As per Estimated Cost (Inclusive of GST) |
Item Description Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface/recessed PVC conduit as required. 2 Pair Estimated Cost (Inclusive of GST) |
Item Description Supply, installation, testing and commissioning of Telephone Sets (analog and digital) shall be line powered from the system and connected on two wires (single pair) only all complete job as per direction of E/I. Make: BEETEL/ Panasonic/Motorola or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Supply, installation, testing and commissioning of 50 PAIR KRONE BOX all complete job as per direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 4.5 metre and upto 6.5 metre Estimated Cost (Inclusive of GST) |
Item Description Supplying, installation, testing and commissioning of 70W LED Solar Street Light On 6 Meter GI octagonal Pole having Compact, Aesthetic, Eco friendly & modern integrated Solar street light in extruted Aluminum construction with high efficiency monocrystalline silicon photo voltaic panel, high efficacy SMD LED 6500K having secondary lens optics for street lighting distribution, high performance lithium battery, MPPT charge controller & Intelligent control module/sensor with higher reliability, long service life, suitable for easy & quick installation. Wipro Cat No.:LR 14-591-XXX-65-XX. or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Providing, installation of 200 x 150 x 125 mm polycarbonate weather proof (IP-55) junction box and SP MCB?s and terminal block. Supplying and laying cable through GI pipe upto junction box including excavation and back filling, wiring with 2 x 2.5 sq.mm PVC insulated 1100 volts grade copper conductor wires from junction box to lighting fixture complete. Estimated Cost (Inclusive of GST) |
Item Description Supplying and laying cable through GI pipe upto junction box including excavation and back filling, wiring with 2 x 2.5 sq.mm PVC insulated 1100 volts grade copper conductor wires from junction box to lighting fixture complete. Estimated Cost (Inclusive of GST) |
Item Description Supply, erection, testing and commissioning of 230V, single phase 2 wire AC to 24V DC Batteries charger ( SMPS Based ) with semiconductor/IGBT fullwave rectifier with auto /manual float cum boost facility complete with 24V DC, 120 AH sealed maintenance free batteries including one no. distribution board having 63 Amps DP MCCB as incomer and 12 Nos. 20/16A DP MCB's (D.C. duty) as outgoing complete as required and as directed by Engineer Incharge. Estimated Cost (Inclusive of GST) |
Item Description DISTRIBUTION TRANSFORMERS: Supply, Installation, testing and commissioning of Oil Type Transformer 800 KVA 11/0.433 KV, 3 Phase, 50 Hz, Dyn 11 vector group, copper wound, class F insulation associated with On Load Tap Changer (OLTC) plus AVR and RTCC Panel for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote manual operation of On Load Tap Changer, winding temperature indicator/ controller actuated by means of resistance temperature detector embedded in LV windings, indoor type Transformer with impedance as per latest ECBC norms, tapping for off load operation on HV side in steps of +5% to - 15% in steps of 1.25% 17 steps to give a constant secondary voltage, having cable end boxes on HV side suitable for 3C x 300 sqmm XLPE cable of 11 KV grade and bus trunking as required on LV side with neutral brought out separately including supplying and laying of copper conductor multicore control cables for safety tripping, suitably mounted on M.S. Channel i/c supplying and grouting of suitable M.S. Channel with all accessories and conforming to IS 11171:1985, IEC 60726, ANSI, NEMA standards & as per specification complete in all respects as required at site. Transformer Losses shall be as per ECBC 2017. Transformer described as above. Estimated Cost (Inclusive of GST) |
Item Description Supplying of following size of aluminum conductor, XLPE insulated armoured and over all PVC sheathed, 11 KV (E) grade earthed cable as per relevant IS code and technical specifications: 3C x 300 sq.mm. XLPE insulated Aluminium. Armored. Cable Estimated Cost (Inclusive of GST) |
Item Description Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm. Estimated Cost (Inclusive of GST) |
Item Description supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 300 sq. mm Estimated Cost (Inclusive of GST) |
Item Description Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 300 sq. mm Estimated Cost (Inclusive of GST) |
Item Description Supply of fire buckets 4 No. in each set duly filled with fine sand and fixed on an angle iron frame as per requirement of local authorities. Fire buckets shall be painted red from outside and white from inside with additional handle at the bottom and suitable for outdoor installation. Estimated Cost (Inclusive of GST) |
Item Description Supply and fixing on position the approved Single Line Diagram framed in 1000 x 800 mm size glass frame and installed in main switch room as directed by Engineer Incharge Estimated Cost (Inclusive of GST) |
Item Description Supply of First Aid box as directed by Engineer Incharge Estimated Cost (Inclusive of GST) |
Item Description Supply of tool kit with 1 pair 11 KV rubber hand gloves as directed by Engineer Incharge. Estimated Cost (Inclusive of GST) |
Item Description Supplying & fixing standard shock treatment charts in English & Hindi duly framed and covered with glass as directed by Engineer Incharge. Estimated Cost (Inclusive of GST) |
Item Description Providing Safety mat made of elastomeric polymers Material (Class B) 1.2 M wide with thickness 2.5 mm to withstand 11KV dielectric strength AS PER relevant IS Code Estimated Cost (Inclusive of GST) |
Item Description Providing a mat made of elastomeric polymers Material (Class A )1.2 M wide with 2 mm thickness to withstand 1.1 KV dielectric strength AS PER relevant IS Code Estimated Cost (Inclusive of GST) |
Item Description SUPPLY, INSTALLATION, TESTING AND COMMISIONING OF DG SET INCLUDING ALL ACCESSORIES: Design, manufacture, supply, erection, testing & commissioning of following rating of DG Sets in Accoustic Enclosure, having self excited & self regulated 415 V, 3 Phase, 4-Wire, 50 Hz, 0.8 p.f. Alternator coupled with multi-cylinder, turbo-charged/ turbo-charged after cooled as called for, Diesel Engine capable to generate the power not less than the required BHP to achieve the alternator capacity as given below, with radiator Cooled, hospital type silencers and Electronic governer (G3 Governing System), DG set controller suitable for Auto Synchronization & Auto Load Sharing with microprocessor based Synchronization relay like Woodward/Dief/ Deepsea or equivalent including providing of Engine control panel, 24V batteries of suitable rating, battery-charger with battery leads, inbuilt oil fuel tank of capacity as per OEM standards and complete with all standard accessories & protection as required and as per specifications, including first filling of lube oil, fuel tank, providing common base plate, anti vibration pads, drip trays, foundation bolts, nuts, bolts, cable termination/adopter box sutiable to terminate upto 8 nos. of 3.5Cx300 sq.mm. XLPE cables as required for a complete installation including RCC/PCC foundation for DG set as per the structural detail for Dynamic Load submitted by the Vendor and approve by the Client. DG set should comply relevant Indian standards. DG shall have Remote Monitoring System. 1010 KVA (With Acoustic Enclosure) Estimated Cost (Inclusive of GST) |
Item Description Supply, installation, testing and commissioning of exhaust pipe fabricated out of 6 mm thick MS pipe Class C Heavy duty conforming to IS:3589 with all fixing accessories and hardwares.The work include necessary cladding of exhaust pipe work using 50 mm thick Loosely bound resin (LBR) mattress/ mineral wool/ Rockwool, density not less than 120 kg/m3 and aluminium cladding (0.6 mm thick) for the complete portion. The exhaust pipe work includes necessary supports, foundation etc. to avoid any load & stress on turbo charger / exhaust piping.The exhaust pipe shall be run along the existing wall of the building duly clamped/supported on independent structure for which, the design and Drawing for such structure shall be got approved from the Engineer-in. 400mm dia Estimated Cost (Inclusive of GST) |
Item Description Design, supply, fabrication and erection of steel structure from channel /angle iron of suitable sizes to support the chimney /exhaust MS pipe duly taking into consideration of the wind load/pressure at the site etc. including the cost of civil foundations as required to support a maximum of 2 nos exhaust chimneys on the overhead platform complete as required. The structure shall be given primer coat and two coats of enamel painting. Estimated Cost (Inclusive of GST) |
Item Description SS Flexible Bellow 400 mm dia Estimated Cost (Inclusive of GST) |
Item Description Aluminium cladding for the residential silencers Estimated Cost (Inclusive of GST) |
Item Description Supply & Fixing of Y Bend for Exhaust pipe Estimated Cost (Inclusive of GST) |
Item Description Supplying, fixing, testing and commissioning of following bare Copper/ GI flat including all necessary fixing accessories and effecting connections. 50 mm x 6 mm thick Cu flat Estimated Cost (Inclusive of GST) |
Item Description Supplying, fixing, testing and commissioning of following bare Copper/ GI flat including all necessary fixing accessories and effecting connections. 50 mm x 6 m thick GI flat Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 2C x 6 sq.mm. (19mm) Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 2C x 10 sq.mm. (19mm) Estimated Cost (Inclusive of GST) |
Item Description Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required. 3.5C x 240 sq.mm. (62mm) Estimated Cost (Inclusive of GST) |
Item Description MAIN LT Panel : Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 55 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks with sleeved TPN Aluminum Bus bars and GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade (RAL 7032) over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. This main panel must be extendable for future requirement in such a manner not to disrupt ongoing services at the point of use during extension. All LT Panel shall conform to latest IS/IEC -61439 code. All Panel shall be complete with power & control wiring, danger & inscription plate, Lifting hooks etc. Each incoming / outgoing breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. All the MCCB with adustable overload, short circuit & earth fault protection and above shall have microprocessor. The panel shall be manufactured as per BOQ, tech specification and drawing. (Note:The contractor may select the next higher fault rating of ACB/ MCCB if it is not readily available ,without any extra cost ,as the figure indicated within the bracket are required maxmum fault level of the panel.) NOTE: PANEL MUST BE AS PER IEC 61439 TYPE TESTED FROM ANY INDIA BASED TEST LABORATORY (CPRI/ERDA ETC) FOR ROTECTION AGAINST SHORT CIRCUIT/TEMPERATURE RISE/INTERNAL ARC/DEGREE OF PROTECTION) (PTTA PANEL UPTO 630A & TTA PANEL ABOVE 630A) Estimated Cost (Inclusive of GST) |
Item Description Capacitor Panel : Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 55 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks with sleeved TPN Aluminum Bus bars and GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade (RAL 7032) over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. This main panel must be extendable for future requirement in such a manner not to disrupt ongoing services at the point of use during extension. All LT Panel shall conform to latest IS/IEC -61439 code. All Panel shall be complete with power & control wiring, danger & inscription plate, Lifting hooks etc. Each incoming / outgoing breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. All the MCCB with adustable overload, short circuit & earth fault protection and above shall have microprocessor. The panel shall be manufactured as per BOQ, tech specification and drawing. (Note:The contractor may select the next higher fault rating of ACB/ MCCB if it is not readily available ,without any extra cost ,as the figure indicated within the bracket are required maxmum fault level of the panel.) NOTE: PANEL MUST BE AS PER IEC 61439 TYPE TESTED FROM ANY INDIA BASED TEST LABORATORY (CPRI/ERDA ETC) FOR ROTECTION AGAINST SHORT CIRCUIT/TEMPERATURE RISE/INTERNAL ARC/DEGREE OF PROTECTION) (PTTA PANEL UPTO 630A & TTA PANEL ABOVE 630A) Estimated Cost (Inclusive of GST) |
Item Description EXTERNAL LIGHTING FEEDER PILLAR-1 (Outdoor Type weather proof, double door with canopy IP-65) : Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 55 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks with sleeved TPN Aluminum Bus bars and GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade (RAL 7032) over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. This main panel must be extendable for future requirement in such a manner not to disrupt ongoing services at the point of use during extension. All LT Panel shall conform to latest IS/IEC -61439 code. All Panel shall be complete with power & control wiring, danger & inscription plate, Lifting hooks etc. Each incoming / outgoing breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. All the MCCB with adustable overload, short circuit & earth fault protection and above shall have microprocessor. The panel shall be manufactured as per BOQ, tech specification and drawing. (Note:The contractor may select the next higher fault rating of ACB/ MCCB if it is not readily available ,without any extra cost ,as the figure indicated within the bracket are required maxmum fault level of the panel.) NOTE: PANEL MUST BE AS PER IEC 61439 TYPE TESTED FROM ANY INDIA BASED TEST LABORATORY (CPRI/ERDA ETC) FOR ROTECTION AGAINST SHORT CIRCUIT/TEMPERATURE RISE/INTERNAL ARC/DEGREE OF PROTECTION) (PTTA PANEL UPTO 630A & TTA PANEL ABOVE 630A) Estimated Cost (Inclusive of GST) |
Item Description Design, manufacture, supply, installation, testing, commissioning, approvals (statutory or otherwise) and handing over in satisfactory working conditions of Elevators with directional collective control for cars (as required) with AC VVVF control with automatic rescue device (ARD) and with, automatic centre opening car door SS finished, vine flooring including the cost of providing 4 weeks satisfactory trial operation and testing at 100% of design load and ALL safety checks including simulation tests of over load, over shoot, over speed, sudden breaks, emergency calls, fire man's switch operation etc. and each elevator to be programmed for jerkless operation and including providing free comprehensive maintenance service for 12 months after final virtual completion and satisfactory handing over as DLP, complete as per specifications as required and as below: 1. Capacity (kgs)-884 Kgs, 2.Passenger -13 Nos., 3.Contract Speed (m/s)-1.0 M/S, 4.Machine-PM Gearless (Located above shaft), 5.Machine Location-Machine Room Less, 6.Operational Control-Duplex Selective Collective. Microprocessor-Based system, 7. Motor Control-AC Variable Voltage Variable Frequency, Microprocessor Based with Digital Closed Loop Feedback. 8. Power Characteristics-400/415 Volts (3 Phase AC) 9. Stops-14 Stops With (all opening on the same side) 10.TRACTION MEDIA- Flat Coated Steel Belt, 11.FALSE CEILING TYPE-Stainless Steel #4(Hairline), 12.Travel height-41.6 Mtrs. (approx.), 13.HOISTWAY DIMENSIONS (W x D ? mm)-1900 mm W x 2400 mm D, 14-CAR DIMENSIONS (W x D x H - mm)- 1100 mm W x 2000 mm D x 2300 mm D, 15. DOOR OPENING (W x H - mm)-800 (W) × 2100 (H), 16-Door Fire Rating-Fire rating-60mins, 17.Door Operation-High Speed, Heavy-Duty Door Operator. Adjustable Door Speed. Centre Opening Door. Minimum opening speed 2-1/2 FPS. 18.CAR DOOR FINISH-Stainless Steel #4(Hairline), 19.Guide Rails-High Strength Steel Class-A / Planed Steel Tees, 20. FLOORING-Vinyl Tiles, 21.Compensation-Provider's standard application, 22.CAR FINISH-Rear Mid Panel = Stainless Steel #4(Hairline), Rear Corner Panels = Stainless Steel #4(Hairline), Side Mid Panels = Stainless Steel #4(Hairline), Side Corner Panels = Stainless Steel #4(Hairline), Front Panels = Stainless Steel #4(Hairline) 23.Signal Fixtures-Provider's Premium Design. 24.HAND RAILS-Stainless Steel Mirror Finish Handrails on rear car panels, 25.LANDING DOORS FINISH-Stainless Steel #4(Hairline) 26.CAR POSITION INDICATOR-Monochrome LCD-Blue Background & White font 27.PIT DEPTH-1600mm, Note: (a) BMS Compatible Power / Control panel for the above Lifts (b) Power and Control cabling for the above lifts (c) Necessary scaffolding for execution to be arranged by lift vendor. (d) Control cabling and panel shall be including with lift items. (e) Power for testing and commissioning shall be provided by owner / client at one point on chargeable basis for the distribution will be in contractor scope. Estimated Cost (Inclusive of GST) |
Item Description Design, manufacture, supply, installation, testing, commissioning, approvals (statutory or otherwise) and handing over in satisfactory working conditions of Elevators with directional collective control for cars (as required) with AC VVVF control with automatic rescue device (ARD) and with, automatic centre opening car door SS finished, vine flooring including the cost of providing 4 weeks satisfactory trial operation and testing at 100% of design load and ALL safety checks including simulation tests of over load, over shoot, over speed, sudden breaks, emergency calls, fire man's switch operation etc. and each elevator to be programmed for jerkless operation and including providing free comprehensive maintenance service for 12 months after final virtual completion and satisfactory handing over as DLP, complete as per specifications as required and as below: 1. Capacity (kgs)-884 Kgs, 2.Passenger -13 Nos., 3.Contract Speed (m/s)-1.0 M/S, 4.Machine-PM Gearless (Located above shaft), 5.Machine Location-Machine Room Less, 6.Operational Control-Duplex Selective Collective. Microprocessor-Based system, 7. Motor Control-AC Variable Voltage Variable Frequency, Microprocessor Based with Digital Closed Loop Feedback. 8. Power Characteristics-400/415 Volts (3 Phase AC) 9. Stops-5 Stops With (all opening on the same side) 10.TRACTION MEDIA- Flat Coated Steel Belt, 11.FALSE CEILING TYPE-Stainless Steel #4(Hairline), 12.Travel height-14.0 Mtrs. (approx.), 13.HOISTWAY DIMENSIONS (W x D ? mm)-1900 mm W x 2400 mm D, 14-CAR DIMENSIONS (W x D x H - mm)- 1100 mm W x 2000 mm D x 2300 mm D, 15. DOOR OPENING (W x H - mm)-800 (W) × 2100 (H), 16-Door Fire Rating-Fire rating-60mins, 17.Door Operation-High Speed, Heavy-Duty Door Operator. Adjustable Door Speed. Centre Opening Door. Minimum opening speed 2-1/2 FPS. 18.CAR DOOR FINISH-Stainless Steel #4(Hairline), 19.Guide Rails-High Strength Steel Class-A / Planed Steel Tees, 20. FLOORING-Vinyl Tiles, 21.Compensation-Provider's standard application, 22.CAR FINISH-Rear Mid Panel = Stainless Steel #4(Hairline), Rear Corner Panels = Stainless Steel #4(Hairline), Side Mid Panels = Stainless Steel #4(Hairline), Side Corner Panels = Stainless Steel #4(Hairline), Front Panels = Stainless Steel #4(Hairline) 23.Signal Fixtures-Provider's Premium Design. 24.HAND RAILS-Stainless Steel Mirror Finish Handrails on rear car panels, 25.LANDING DOORS FINISH-Stainless Steel #4(Hairline) 26.CAR POSITION INDICATOR-Monochrome LCD-Blue Background & White font 27.PIT DEPTH-1600mm, Note: (a) BMS Compatible Power / Control panel for the above Lifts (b) Power and Control cabling for the above lifts (c) Necessary scaffolding for execution to be arranged by lift vendor. (d) Control cabling and panel shall be including with lift items. (e) Power for testing and commissioning shall be provided by owner / client at one point on chargeable basis for the distribution will be in contractor scope. Estimated Cost (Inclusive of GST) |
Item Description WARDEN Table Trident Middle of size 1650 x 700 x 743 (Main Desk) 1000 x 450 x 743 (ERU)-Main Desk with ERU Size 1650 x 700 x 743 (Main Desk) 1000 x 450 x 743 (ERU) Understructure: The understructure is in prelam panels, made with PLT boards.2Drawer and 3Drawer storage units with different combinations to support Tops, made with 18mmPLT boards of different colours. Modesty and back panels, made with 18mm PLT boards. The Pedestals/Storages are fitted with necessary Locks PLT Board Tops (Straight Edges): Wenge and Savannah Maple PLT board used for making Tops. PVC membrane Tops (with profiles) (Godrej, Haworth , BP ERGO LTD. or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description WARDEN-Parto Two Seater Sofa Dimensions W x H x D (mm) 1320 x 830 x 860-Two Seater Sofa Dimension of 2 Seater 1340W x 870D x780H , made of PVC Upholstery, Frame Material : Tropical Solid Wood joined by means of hardened steel screws and steel bolts, as well as glue, Seat Foam : Slab stock foam along with recron sheet. Foam Density : 17 kg/ cubic cm, Back Foam : Slab stock foam with recron fill. Foam Density : 17 kg/cubic cm, Webbing : S-spring with cross membrane (Godrej, Haworth , BPERGO LTD. or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Edward Corner Table of size 600mm W x 600mm D x 455mm H-Coffee Table of size 1200 x 600x450 mm is reminiscent of the retro charm of the Victorian Era. The table top is made of high-density plywood which makes it a sturdy piece of furniture. The beautifully curved legs give a rich feel to the table. You can also place a lot of food and heavy ornaments on the table owing to the thick table top and a wide surface which can hold up to 50 kilograms of weight. The walnut finish of the table doesn't just look elegant but allows it to be placed in any kind of setting without seeming out of place (Godrej, Haworth , BPERGO LTD. or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description ROOM-Supplying & Installing of Single sheet bed of standard ayush semi fowler Bed of Size 2265Lx900Wx610Hmm with 2 Section Mattress 100mm. Make-Godrej /Durian/Zuari/Methodex or equivalent as per direction of engineer incharge. Estimated Cost (Inclusive of GST) |
Item Description ROOM-Supplying & Installing of 2 Door Wardrobe Overall Size including top : Width - 960.0 mm Depth - 590 mm Height - 1941.0 mm, Material : Body panels are made of 18 mm thick Prelaminated Particle Board All the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Door are made of 18 mm thick Prelaminated Particle board with all the exposed edges are edge banded with 0.8 mm thick PVC edge banding and with imported H.D.F. foil wrapped decorative trim fixed on to it. Drawer components are made of 18 mm thick Prelaminated Particle Board .All the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Body back and drawer bottom are made of 8 mm thick Prelaminated particle board. Top cornice is made of imported H.D.F. foil wrapped decorative Trim. Hardware : The high quality hardware used like Roller slides, Hinges , minifix, wooden dowels is of make Hettich.. Lock used for middle door is 3 way lock. Lock used for right hand door and drawer is cam lock Construction : Knock Down construction. Finish :18 mm thick Prelaminated Particle Board is in Maple shade(Make-Methodex, Godrej, Durian or equivalent as per direction of engineer incharge) do all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description ROOM-Supplying & Installing of Study Table with Desk Panel are made of 18mm thick pre-laminated Board with PVC edge banding on all sides. Understructuremade of Dia 19.05x1.25 mm thick powder coated ERW at base.the Storage Shelf is made from 0.6 mm thick..Size of Table (600Wx400Dx740H) (Make-Godrej /Durian/Zuari/Methodex or equivalent as per direction of engineer incharge) as per direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supplying & Installing of CHAIR without arm with SEAT/BACK: The Seat and Back should be made of injection moulded high impact strength Polypropylene polymer compound with indoor grade UV resistance. SEAT SIZE: 52.5 cm. (W) x 53.2 cm. (D), * BACK SIZE : 51.6 cm. (W) x 40.5 cm. (H) .S.S. UNDERSTRUCTURE: The tubular welded frame made by Stainless Steel 202 grade tube dully buff polished to give shiny finish (Make-Godrej /Durian/Zuari/Methodex or equivalent as per direction of engineer incharge) as per direction of E/I Estimated Cost (Inclusive of GST) |
Item Description FOR STAFF ROOM-Matrix Three Seater Chair Overall Size - 1695mm W x 638mm D x 785mm H x 441mm SH-Three Seater Chair with Common Arms - seat shell : the seat shell should be a welded assembly of seat,back and side frame. the seat and back should be made of 0.12±0.013cm thk cr steel sheet with oblong perforations.they should be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should be powder coated ( dft 40-60 microns ). the seat has a front water fall edge to provide popliteal clearance for comfortable seating. it also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. clean and flat surfaces of seat and back aids in easy maintenance. * seat size : 47.8 cm (w) x 44.6 cm (d) * back size : 41.6 cm (w) x 23.0 cm (h) understructure assembly: understructure assembly consshould be ts of connecting beam and leg assembly made of m.s. e.r.w. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.the welded structure assembly should be powder coated ( dft 40-60 microns ).the leg assembly should be fitted with shoes and levellers in nylon. the leg structure should be designed with minimal should be a of contact close to ground providing easy access for cleaning purposes. the shoes fitted to leg assembly help in aligning the structure for back to back arrangements. levellers take cshould be of uneven flooring. connecting beam should be fitted with snap locking end cap.lt also aids in side-by-side understructure alignment arm rest assembly: armrest assembly consshould be ts of armrest frame and armrest pad . the armrest frame should be made up of size 3.175±0.05cm x 0.47±0.027cm thk hr steel and it should be powder coated ( dft 40-60 microns ). armrest pad should be injection molded in nylon and should be fitted onto the armrest frame. (Godrej, Haworth, BP ERGO LTD. or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Steel MF System of size 6'x36"x18" with Six Shelves-Steel MF System of size 6'x36"x18" with Six Shelves -Prime quality CRC sheet conforming to IS 513D/10748/5986. The pitches of the slots at 19.05 mm, Panel/Shelves: 6 Bnd bending process of 905L x 448D of load capacity 80 Kgs. UDL Max Per shelf. Shelf Material- 0.8 mm Thick MS Sheet Conforming to Commercial Quality CR-1, Grade 340 of IS 513, Angle Posts Material and size-Rolled steel angle posts of 40 X 40 X 1.8 mm, M S Sheet Thickness of Shelves and Back (Minimum) in mm-0.8, Paint-Powder coated with Lead Free Paint (Godrej, Haworth, BP ERGO LTD. or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Table Time Out of size 1734 x 1175 x 750-DINING & MULTIPURPOSE HALL- Table of size 1734 x 1175 x 750 Top shall be 25 mm thick base material shall be 25 mm MDF board . On top PU painting of minimum 2H hardness with 75% glass as per color chart .Combination color graphics on the centre . Brown Laminate on bottom specially profiled edges for comfort . The Understructure shall be having bend pipe structure of MS powder coated . Pipe dia 38 mm , 2 mm thick and it shall be fitted with top by SS machine screws . Legs shall be of MS powder coated and 38 mm dia. pipe legs are fixed with inderstructure and table top . Glide shall be of Plastic fixed at the understructure to prevent the damage of table top during stacking . (Godrej, Haworth, BP ERGO LTD. or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Shine Universal Chair MS Understructure -FOR MULIPURPOSE HALL-The product should be SCS Indoor Advantage Gold, BIFMA LEVEL 2 & Greenguard UL certified Shine Universal Chair MS Understructure Overall size WIDTH - 515mm x DEPTH - 525mm x HEIGHT - 818mm x SEAT HEIGHT - 459mm SHELL : The single piece seat back shell is made up of injection moulded high impact strength glass filled polypropylene polymer compound (refer product catalogue for colour chart). * SHELL SIZE : 44.0 cm. (W) x 50.2 cm. (D) x 40.5 cm. (H) S.S. UNDERSTRUCTURE OPTION (SM6) : The tubular welded frame is made from Dia 2.22 ± 0.03 cm x 0.15 ± 0.0128 cm Stainless Steel 304 grade tube which is buff polished. The 0.16 ± 0.008 cm thk Stainless Steel 304 CRCA sheet is welded to tubes for fixing shell to the frame.The shoe is made of high impact strength polypropylene polymer compound and are fitted at the end of the tubular frame. (Godrej, Haworth , BP ERGO LTD. or equivalent as per direction of engineer incharge) Estimated Cost (Inclusive of GST) |
Item Description Supplying & Installing of Chair (CH4) - Office chair with cantilever type frame made of dia. 2.54 cm x 14 BG thick M.S.ERW tube and powder coated without arm. Seat/Back made of chemically treated and seasoned wood, caned and furnished with melamine polish. Back size - 38.1 cm (W) x 42.4 cm (D). The under structure assembly is a cantilever type frame made of dia 2.54 cm x 14 BG thick M.S.ERW tube and powder coated, complete in all respect ct perference make (GODREJ / METHODEX / DURIAN / JUARI or equivalent as per direction of engineer incharge) as per direction of Engineer-in-charge. Estimated Cost (Inclusive of GST) |
Item Description WASHING ROOM-Supplying & Installing of Table made of MS ERW round tube dia 25.4 x 1.2mm thick with 18mm thick Pre Laminated top size 1199 X 590 X 735 with one side three drawer unit made of .5mm thick CRCA sheet mild steel, All steel components have powder coated paint fitted with lock of make- Methodex, Godrej, Durian or equivalent as per direction of engineer incharge) do all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description MANAGER CHAIR+WARDEN- Supplying & Installing of Bravo Mid Back Chair with seat and back are made up of 1.2 cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. Dimension BACK SIZE - 47.5 cm. (W) x 58.0cm. (H) & SEAT SIZE 47 0 cm. (W) x 48.0 cm. (D). POLYURETHANE FOAM: The Polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +1- 2 at 25% compression 3) ARMRESTS The one-piece armrests are injection moulded from black Co-polymer Polypropylene. 4) CENTER TILT SYNCHRO MECHANISM, PNEUATIC HEIGHT ADJUSTMENT, complete in all respect of perference make (GODREJ / METHODEX / DURIAN / JUARI or equivalent as per direction of engineer incharge) as per direction of Engineer-in-charge. Estimated Cost (Inclusive of GST) |
Item Description ASST. PROF.+ASSO. PROF. CHAIR-Supplying & Installing of Visitor Chair for PRINCIPAL : CHAIR with Cantilever type frame made of dia 2.54cm x 14 BG thick M.S.ERW tube and coated without arm. Seat/Back made of chemically treated and seasoned wood, caned and furnished with melamine polish. BACK SIZE-38.1 cm (W) X 42.4 cm (D). The seat should be extra thick foam on front edge to give comfort to popliteal area (Make-Godrej/Durian /Zuari/Methodex or equivalent as per direction of engineer incharge) as per direction of E/I Estimated Cost (Inclusive of GST) |
Item Description MANAGER TABLE-Table Model Insight 1800W Dimenstion- 1800 x 900 x 740 made of Worktop- 25 mm Thick PLB Tops with 2mm Thick PVC Edge Beading, Understructure C - Frames 1.6 mm thick M.S CFrame Supporting the Top., Legs- Dia. 38.1 x 1.6 mm thick M.S ERW tube, complete in all respect of perference make (GODREJ / METHODEX / DURIAN / JUARI or equivalent as per direction of engineer incharge) as per direction of Engineer-in-charge. Estimated Cost (Inclusive of GST) |
Item Description MANAGER ROOM-Supplying & Installing of Steel Storwel Plain with Four Shelves Almirah of size 1980 x 916 x 486 MM multi bend construction and inter locking design and full length over apping doors and sides. Three-way bolting mechanism. Spot welding & CO2 weldipg. Anticorrosion treated components, oven baked powder coatinq process. Material thickness 0 9mm Top, Bottom.LH & RH sides and back material thickness - 0.9 mm, removable RH & LH main door with stiffeners materials thickness - 0.9 mm, 4 adjustable shelves of thickness - 0.8 mm, complete in all respect of perference make (GODREJ / METHODEX / DURIAN / JUARI or equivalent as per direction of engineer incharge) as per direction of Engineer-in-charge. Estimated Cost (Inclusive of GST) |
Sum(Estimated Cost (Inclusive of GST)): () |