Item Code | Item Description | UOM | QUANTITY | Rate | GST (%) | GST Value | Estimated Cost (Inclusive of GST) | Mandatory Item |
1 | 415V LT DG SET Supply, Installation, testing & Commissioning of 500 KVA Silent DG set along with 415V AC Power distribution board comprising of suitable engine coupled to 415V Stamford make alternator both mounted on common base frame with other standard accesies i.e. Fuel tank, Batteries with leads. On Mains failure the DG set shall be started by means of a switch on the control panel. | SET | 2 | | | 0 | 0 | Yes |
2 | Transformer - 630 KVA 11/0.433kVA Out door Oil Type Supplying/Receiving, Installation/Erection, Testing and Commissioning of 630kvA ONAN, Copper wound 11/0.433 KV, 50 C/S, Delta star connected, Dyn11 vector group, Oil immersed Outdoor transformer with Off Load circuit Tap changer for Voltage regulation from -10% to +15% in 7 steps of 1.25% on HV side complete with AVR and RTCC panel, including Bucholtz relay, MOG, Oil & Winding temperature alarm and trip contacts with wiring upto marshalling box, and all standard accesies as required, complete with Cable End box suitable for 1RX3C x 95sq.mm. 11 KV(UE) XLPE insulated Al. Ar. Cable at HT side and XLPE insulated Al. Busduct for LT side, including S/F of M.S. channel of size 100 x 50 x 6mm for foundation support for transformer, including Drying/filtration of oil of transformer and OLTC Enclousere.Connection with Tap Changing Mechanism etc. as per IS 2026-1977. Rate of SITC of 630kVA Transformer after analysis | SET | 2 | | | 0 | 0 | Yes |
3 | Transformer - 500 KVA 11/0.433kVA Out door Oil Type Supplying/Receiving, Installation/Erection, Testing and Commissioning of 500kvA ONAN, Copper wound 11/0.433 KV, 50 C/S, Delta star connected, Dyn11 vector group, Oil immersed Outdoor transformer with Off Load circuit Tap changer for Voltage regulation from -10% to +15% in 7 steps of 1.25% on HV side complete with AVR and RTCC panel, including Bucholtz relay, MOG, Oil & Winding temperature alarm and trip contacts with wiring upto marshalling box, and all standard accesies as required, complete with Cable End box suitable for 1RX3C x 95sq.mm. 11 KV(UE) XLPE insulated Al. Ar. Cable at HT side and XLPE insulated Al. Busduct for LT side, including S/F of M.S. channel of size 100 x 50 x 6mm for foundation support for transformer, including Drying/filtration of oil of transformer and OLTC Enclousere.Connection with Tap Changing Mechanism etc. as per IS 2026-1977. Rate of SITC of 500kVA Transformer after analysis | SET | 1 | | | 0 | 0 | Yes |
4 | LT Switchboard-1 (Indoor Type) Design, Fabrication, Supply, Erection,Testing and commissioning of Powder coated Main LT Switchboard fabricated out of 14 gauge CRCA sheet steel in cubical, compartmentalised, free standing floor /wall mounted, dust and vermin proof, (degree of protection IP42)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels. Approval shall be taken for each panel before fabrication. (All hardware's like nuts and bolts used shall be Galvanized and Zinc passivated)As per Specification and LT Switchboard shall be comprising broadly of the following equipment's Incomer: 1000Amps, S.C.C 50kA for 1 Sec ACB (EDO) - 2 Nos. 1 Bus coupler 1000Amps, S.C.C 50kA for 1 Sec ACB Outgoing Feeders: 4 Pole, MCCB (P-2), (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links 400 Amps - 2 Nos. (35/36 kA S.C.C) 250 Amps - 2 Nos. (35/36 kA S.C.C) 160 Amps - 15 Nos. (35/36 kA S.C.C) 100 Amps - 15 Nos. (25 kA S.C.C) Aluminium Bus 1000 Amps, S.C.C 40kA for 1 Sec CT, PT, MCBs, Ammeter, Voltmeter with Selector Switches, Energy meter,indication lamps(On- Off Trip, Power On - RYB) 630Amps Isolator, S.C.C 35kA for interconnection with DG Set | SET | 1 | | | 0 | 0 | Yes |
5 | LT Switchboard-2 for Quarters (Indoor Type) Design, Fabrication, Supply, Recontesting and commissioning of Powder coated Main LT Switchboard fabricated out of 14 gauge CRCA sheet steel in cubical, compartmentallised, free standing floor /wall mounted, dust and vermin proof, (degree ofprotection IP42)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated)As per Specification and LT Switchboard shall be comprising broadly of the following equipments Incomer each 800Amps, S.C.C 50kA for 1 Sec ACB (EDO) 1 Buscoupler 800Amps, S.C.C 50kA for 1 Sec ACB Outgoing Feeders: 4 Pole, MCCB (P-2), (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links 400 Amps - 2 Nos. (35/36 kA S.C.C) 250 Amps - 2 Nos. (35/36 kA S.C.C) 160 Amps - 15 Nos. (35/36 kA S.C.C) Aluminium Bus 800 Amps, S.C.C 40kA for 1 Sec CT, PT, MCBs, Ammeter, Voltmeter with Selector Switches, Energy meter, indication lamps(On- Off Trip, Power On - RYB) | SET | 1 | | | 0 | 0 | Yes |
6 | LIGHTING DISTRIBUTION BOARD FOR STREET LIGHTING (LDB). Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Lighting dist. Boards (LDB), fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing, dust and vermin proof, (degree of protection-IP42)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated)As per Specification. Each LDB shall broadly comprise of the following equipment/components) Incomer: 100A, 4 Pole, MCCB (P-2), 25kA S.C.C (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links - 1 No. Outgoing feeders: 4 Pole, MCCB (P-2), (Ics=100%Icu) 16kA S.C.C Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links 63A TPN MCCBs - 2 Nos. 63A TPN MCBs - 15 Nos. Indication lamps(On- Off Trip Power On -- RYB),200 A aluminium bus, s.c.c 35 KA for 1s | SET | 1 | | | 0 | 0 | Yes |
7 | AC DISTRIBUTION BOARD : Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Aux.Power dist. Boards (Aux.PDB), fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing, dust and vermin proof, (degree of protection-IP42)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated)As per Specification. Each ACDB shall broadly comprise of the following equipment/components) Incomer: 160A, 4 Pole, MCCB (P-2), (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links - 1 Nos. Outgoing feeders : 4 Pole, MCCB (P-2), (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links 100A, TPN MCCBs - 2 Nos. (25kA S.C.C) 63A TPN MCCBs - 6 Nos. (16kA S.C.C) Indication lamps(On- Off Trip Power On -- RYB), 300 A aluminium bus, s.c.c 35 KA for 1s | SET | 2 | | | 0 | 0 | Yes |
8 | ESE Make: 3 Phase 415 VAC, 50Hz contract type 200 KVAR APFC standard specification with delta connected capacitor bank. | each | 3 | | | 0 | 0 | Yes |
9 | Public Address System | No | 4 | | | 0 | 0 | Yes |
10 | Transmitters | No | 60 | | | 0 | 0 | Yes |
11 | MAIN DESK- Top Panel: Made of 90mm Thick (41mm) using MDF and Veneer. Finish- PU Coating, Scratch Resistance 2H Leg: Made of 25mm thk using MDF and Veneer with PU coating. Modesty: Made of 16mm thk using MDF and Veneer with PU coating. ERU- Top Panel: Made of 25mm Thick (+imm) using MDF and Veneer. Finish- PU Coating, Scratch Resistance 2H Other Panel: Made of 18mm Thick (41mm) Pre-Lam Particle Board. Drawer base : Made of 8mm thick (41mm) Pre-Lam Particle Board. Castor: Dia - 40mm & height 55mm (6 no.s lockable) Finish- Veener with PU Coating 2DR/3DR PEDESTAL- Top Panel: Made of 25mm Thick (41mm) using MDF and Veneer Other Panel: Made of 18mm Thick (41mm) Pre-Lam Particle Board. Castor: Dia - 40mm & height 55mm (2 lockable & 2 unlockable) Finish- Veener with PU Coating. As per the direction of engineer-in-charge. | each | 13 | | | 0 | 0 | Yes |
12 | BACK UNIT- Top Panel: Made of 18mm Thick (£1mm) Pre-lam Particle Board. Finish: Veener with PU Side Panel : Made of 16mm Thick (41mm) Pre-lam Particle Board. Shelf Panel: Made of 22mm Thick (41mm) Pre-Lam Particle Board. Door Panel: Made of 18mm Thick (41mm) MDF Board. Upper door : Made up of 5mm thick Glass.As per the direction of engineer-in-charge. | each | 72.5 | | | 0 | 0 | Yes |
13 | The Main table shall be of size 2400 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm. As per the direction of engineer-in-charge. | each | 45 | | | 0 | 0 | Yes |
14 | Back Unit Dimension- 2215 x 410 x 2000As per the direction of engineer-in-charge. | each | 45 | | | 0 | 0 | Yes |
15 | MAIN DESK-Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management.Modesty Panel-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Under-structure-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeonfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Hinge DoorStorage-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Handle is provided for ease of opening.Storage is provided with cam lock for security. Integrated Pedestal -Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thickMDF one side pre-laminate board confirming toIS-14587:1998 with 0.4mm PVC membrane pressed on to topPedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metalPanel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. As per the direction of engineer-in-charge. | each | 31.5 | | | 0 | 0 | Yes |
16 | MAIN DESK-Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Gromet provided on work surface for wire management. Modesty Panel-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Under-structure-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeonfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge DoorStorage-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening.Storage is provided with cam lock for security. Integrated Pedestal -Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thickMDF one side pre-laminate board confirming toIS-14587:1998 with 0.4mm PVC membrane pressed on to topPedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metalPanel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. As per the direction of engineer-in-charge. | each | 10 | | | 0 | 0 | Yes |
17 | The main desk of shall be of size 1800 Width mm x 900 Depth mm x 750 Height mm.The table top shall be 25 mm thick MFC (Melamine Faced Chipboard) also there should be 30 mm MDF (Medium density fiberboard) black pad.The modesty panel shall be of 18 mm thick MFC (Melamine faced chipboard).The leg of the main desk shall be of 25 mm MFC plus 30 mm MDF right and left pad.The main table should be of duck noise profile edge in order to enhance the workspace aesthetics. The maestro return desk size shall be 1200 Width mm x 600 Depth mm x 730 Height mm.The top panel shall 25 mm thick MFC ( Melamine Faced Chipboard) .The Modesty panel shall be 18 mm thick MFC coated. The leg of the return desk shall be 25 mm thick MFC (Melamine faced chipboard) plus the right and left pad should be 30 mm thick MDF (medium density fiber ) coated. The Maestro Mobile Pedestal size shall be 400 Width mm x 560 Depth mm x 560 Height mm.The top panel shall be 25 mm thick MFC( Melamine Faced Chipboard) plus all the other panels shall be 18 mm thick coated with MFC (Melamine Faced Chipboard). In Mobile pedestal all other panels shall be of 18 mm thick MFC (Melamine Faced Chipboard).In Mobile pedestal lock and Castors shall be Provided. The handle shall be of Metal. The maestro joining table RHS shall be of size 1200 Width mm x 1050 Depth mm x 750 Height mm.The top panel shall be 25 mm thick with MFC (Melamine Faced Chipboard).The leg of the joining table shall be of metal.Pigmented Polyurethane Coated joining table. As per the direction of engineer-in-charge. | each | 13 | | | 0 | 0 | Yes |
18 | Book Case Unit of size 790 x 400 x 2200 made of 25mm Thick (±1mm) MDF Board with 2 side PU painted finish & hardness 2H. Leg:Made of metal tubes.As per the direction of engineer-in-charge. | each | 90 | | | 0 | 0 | Yes |
19 | Back Unit of size 1400 x 470 x 760 made of 25mm Thick (±1mm) MDF Board with 2 side PU painted finish & hardness 2H. Leg:Made of metal tubes. As per the direction of engineer-in-charge. | each | 27.5 | | | 0 | 0 | Yes |
20 | Desk With ERU LHS size shall be 2100 Width mm x 1600 Depth mm x 765 Height mm .The main top shall be of Particle board (Melamine Finish) 1800 x 795 mm.The top shall be 25 mm thick plus 15 mm frame and 2 mm PVC lipping on top .Also there shall be 0.35 mm PVC lipping on frame.The Modesty panel shall be 1100 x 405 x 46 mm thick particle board (Melamine Finish) with 0.35 mm thick PVC lipping.The Drawer Front shall be of size 500 x 170 x 16 mm thick Particle board (Melamine Finish) with 0.35 mm thick PVC lipping.The KBPT shall be 578 W x 284 D x 16 mm with 0.35 mm Thick PVC lipping.The ERU shall have all panels of 16 mm thick Particle board (Melamine Finish).As per the direction of engineer-in-charge. | each | 13 | | | 0 | 0 | Yes |
21 | Table of size 1500 x 750 x 740 TABLE TOP The panel is made from 25 $0.5 mm THK Pre Laminated Boards as per lS?12823 with 2 mm Thick PVC beading on all sides SIDE PANEL -The panel is made from 25 $0.5 mm THK Pre Laminated Boards as per lS?12823 with 2 mm Thick PVC beading on user sides and 0.8 mm on Top & Bottom side. The side panels have 2 glide screws each for leveling of the desk. MODESTY PANEL -The panel is made from 18 $0.5 mm THK Pre Laminated Boards as per lS-12823 with 0.8 mm Thick PVC beading on all edges.FREE STANDING PEDESTAL- The free standing pedestal is made from 18 :05 mm THK Pre Laminated Boards as per lS-12823 with combination of 2mm & 0.8 mm Thick PVC. As per the direction of engineer-in-charge. | each | 65 | | | 0 | 0 | Yes |
22 | OFFICE TABLE Office Table made of MS ERW round tube dia 25.4 x 1.2mm thick with 18 mm thick Pre Laminated top size 1365 X 680 X 735 (Approx.) with both side drawer unit one side three drawers & another side two drawers made of .5mm thick CRCA sheet mild steel, All steel components have powder coated paint fitted with both side drawer lock. As per the direction of engineer-in-charge. | each | 75 | | | 0 | 0 | Yes |
23 | Table 900 X 590 X 750 made of MS ERW round tube 18 mm x 25mm x 1.2mm thick with Pre Laminated top size 1199 X 590 X 750 mm thick with single side one drawers, Drawer unit made of .5mm thick MS CRCA sheet, All steel components have powder coated paint. As per the direction of engineer-in-charge. | each | 68 | | | 0 | 0 | Yes |
24 | Office Table made of MS ERW round tube dia 25.4 x 1.2mm thick with 18mm thick Pre Laminated top size 1199 X 590 X 735 mm with one side one drawer unit made of .5mm thick CRCA sheet mild steel, All steel components have powder coated paint fitted with lock. As per the direction of engineer-in-charge. | each | 68 | | | 0 | 0 | Yes |
25 | Study Table Study Table made of 15mm MDF for table/drawer front 14mm MDF for inner drawer left & right. 3mm for drawer bottom,15mm PB for other panels,0.18mm PVC vacuum laminating for surface of table top and drawer front, 0.4mm lippingfor other panels. Load bearing capacity (table top):35 Kg. Construction: Knock down fitting Dimension- 1000L x 480 W x720H. As per the direction of engineer-in-charge. | each | 70 | | | 0 | 0 | Yes |
26 | Computer Table Model Companion C-2 size 1200 (W) x 600 (D) x 750 (H) made of 18mm thick Pre-Laminated Board with PVC edge banding. Panel of 18mm thick Pre-Laminated Board with Single extrusion slide for Key Board fitted with 4 Nos. Caster. As per the direction of engineer-in-charge. | each | 125 | | | 0 | 0 | Yes |
27 | Table Size-600W x 450D x 750H mm Compact and easy to use . There is enough space to accommodate a printer shelf and CD rack. small, but truly luxurious in space.Top made-up of 1.5 cm Medium Density Fiber. All the other panels are made of Particle board. Vacuum lamination of pvc has been done on the table to surface. 0.4mm lapping is used for all the other panels. As per the direction of engineer-in-charge. | each | 72.5 | | | 0 | 0 | Yes |
28 | Reception Table Double Arch with DL Top of size 2410 x 1065 x 725-Worksurface, 1035-Counter, D L Top Top-Clean matt PU finish 18mm thick Inside radius 700.0 Mm Outside radius ? 1350.0 mm Depth ? 650 mm Glass-Frosted Glass 10mm thick Diamond cut finishing on edges Inside Radius ? 1202.5mm Outside radius ? 1402.5mm Depth ? 200mm, Modesty Panel-MS Perforated sheet Below Worksurface : 0.8 mm (thick) x 665.0 mm (height) x 1345.0 mm (flat length) Above Worksurface : 0.8mm (Thick) x 260 mm (height) x 1345.0 mm (flat length), Legs-MS tube 1.6 mm thick Diameter 50.8 mm Height 604 mm. As per the direction of engineer-in-charge. | each | 3.5 | | | 0 | 0 | Yes |
29 | Conference Table-Material of work top -25 mm thick prelaminated particle board, Table top plain side-Edge banded with PVC tape of 2 mm thick with help of hot melt glue, Material of Gable end and modesty panel-18 Mm Thick Three Layers Prelaminated Particle Boards Of Grade-II Type-III Of IS:12823/Latest Both Sides Particle Boards Matching With Top Shade In Grade-II Type-III, Length of Each Seat of Work Top ± 20 mm- 675 mm for single AND 1350 mm For dual,Depth of Work Top-600mm, Height of Work Top-750 mm, Corners of work top -850 mm, Table top finish-Laminate In Colour With matt Finish 0.6-0.8 Mm Thickness Of Type S,F Or P Having Index Number 3.2.3 Conforming To IS:2046/Latest With Having Balancing Laminate Of 0.5 Mm Thick On Other Side. As per the direction of engineer-in-charge. | each | 10.5 | | | 0 | 0 | Yes |
30 | Conference Table-Material of work top -25 mm thick prelaminated particle board, Table top plain side-Edge banded with PVC tape of 2 mm thick with help of hot melt glue, Material of Gable end and modesty panel-18 Mm Thick Three Layers Prelaminated Particle Boards Of Grade-II Type-III Of IS:12823/Latest Both Sides Particle Boards Matching With Top Shade In Grade-II Type-III, Length of Each Seat of Work Top ± 20 mm- 675 mm for single AND 1350 mm For dual,Depth of Work Top-600mm, Height of Work Top-750 mm, Corners of work top -850 mm, Table top finish-Laminate In Colour With matt Finish 0.6-0.8 Mm Thickness Of Type S,F Or P Having Index Number 3.2.3 Conforming To IS:2046/Latest With Having Balancing Laminate Of 0.5 Mm Thick On Other Side. As per the direction of engineer-in-charge. | each | 7 | | | 0 | 0 | Yes |
31 | HIGH BACK CONFERENCE CHAIR WITH FIX BACK, FIX SEAT & FIX ARMREST- SEAT/BACK ASSEMBLY:The seat is made up of 1.2 +0.1cm. thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back is made up 1.2 +0.1cm. thick hot pressed plywood measured as per QA method describedin OCP-OQLTA-P14-18 and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam is designed with contoured lumber support for comfortable seating posture. *HIGH BACK SIZE 48cm.(W) X 76.0cm.(H) *SEAT SIZE 51.0cm.(W) X 48.0cm.(D) HIGH RESILIENCE (HR) POLYURETHANE FOAM:The HR polyurethane foam for seat and back is moulded with density = 45 +/-2 kg/m* and Hardness load 16 + 2 kgf as per 1S:7888 for 25% compression.ARMREST(FIXED)-The armrest top is moulded from polyurethane (PU) and moulded on to a fixed type tubular armrest support made of @3.8140.03 cm x 0.240.01 cm thk M.S. E.R.W tube having chrome plated finish. KNEE TILT SYNCHRO MECHANISM WITH SEAT DEPTH ADJUSTMENT MECHANISM. The mechanism is designed with the following features 360° revolving type, Single point control, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 4-position locking with anti-shock feature FRONT PIVOT SYNCHRO MECHANISM: The mechanism is designed with the following features: 360° revolving type. Single point control. Front pivot for tilt with feet resting on ground ensuring more comfort. Tilt tension adjustment. 4-position locking with anti-shock feature.FIXED SPINE The seat and back are arrested together with fixed type spine i.e no back up/down adjustment; made of 0.8 40.05 cm thk HR Steel andiis black powder-coated ( DFT 40-60 microns). PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0£0.3 cm.TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. As per the direction of engineer-in-charge. | each | 225 | | | 0 | 0 | Yes |
32 | Very High Back Chair SEAT/BACK ASSEMBLY: The seat is made up of 1.2 1 0.10m. thick hot pessed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with leather and moulded . Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. The chair is available in three models SIZE: 53.0cm.(W) X 95.4cm.(H), SEAT SIZE: 54.6cm.(W) X 49.00m.(D). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness load 16 i 2 kgf as per IS:7888 for 25% compression. SEAT-BACK CONNECTING SPINE:The seat and back are arrested together with ?spine made of 0.8, 10.05 cm thk HR Steel and is black powder-coated ( DFT 40?60 microns ). ARMREST ASSY: The armrest assy. comprises of three parts viz. the armrest support tube and P.U.armrest and the armrest top. The armrest tube assy. is made of 2.54:0.03cm x 0.16:0.0128cm M.S. E.R.W. support tubes and Chrome plated. The P.U. armrest is made of black integral skin polyurethane with 50-70 shore 'A' Hardness and reinforced with MS. insert. The armrest top is made of ABS & upholstered with foam & leather.Static seat depth adjustment = 5.0 i 0.5cm with 5 position locking.PNEUMATIC HEIGHT ADJUSTMENT: it has an adjustment stroke of PNEUMATIC HEIGHT ADJUSTMENT (for PCH-9202RV): it has an adjustment stroke of 12.0 .TELESCOPIC BELLOW ASSEMBLY (for PCH-9202RV): The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSY: The pedestal is made of die-cast aluminium with buf?ng finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 i 0.5cm pitch~center dia. (77.0 i 1.00m with castors). TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon. As per the direction of engineer-in-charge. | each | 140 | | | 0 | 0 | Yes |
33 | Very High back chair with headrest- SEAT/BACK ASSEMBLY: The seat is made up of hot pressed moulded reconstituted wood of 1.240.1cm thickness and backis two part injection moulded plastic.SEAT SUB ASSEMBLYSIZE: 49.0cm (W) X 49.5cm (D), BACK SUB ASSEMBLYSIZE: (HIGH BACK): 46.0 cm (W) X 57.0 em (H)., HEAD REST SUB ASSEMBLYSIZE: 26.0cm (W) X 12.0 cm (L) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam is moulded with Density = 45 kg/m* and Hardness load 16 + 2 kgf as per 1S:7888 for 25% compression. ARMRESTS -The armrests are Pressure die casted in polished Aluminium with PP Arm, Tops. PNEUMATIC HEIGHT ADJUSTMENT-The pneumatic height adjustment has an adjustment stroke of 10.0 t0.3cm. ADJUSTABLE BACK SUPPOR: The backrest is connected to the mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0£0.5cm for the comfortable back support to suitable individual need. PEDESTAL ASSEMBLY(FOR SE 00/01/02TX }: The pedestal is Pressure Die cast polished Aluminium and fitted with 5 nos. twin-wheel castors. The pedestal is 65.0£0.5cm.pitch-centre-dia.(75.0 1.0cm. with castors). HEADREST -The headrest assembly is consist of Leather upholstered and inner with PU foam with density =45 kg/m®. It has swiveling movement. As per the direction of engineer-in-charge. | each | 35 | | | 0 | 0 | Yes |
34 | Full Back Chair with Head Rest Seat/Back Assembly: The Cushioned seat assembly consists of seat outer (material-30% Glass Fiber Nylon) & upholstered Seat inner (material-Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back is mad up of Back outer (material-Glass Fiber Filled Nylon) & Back inner (material-PP) and upholstered using Polyester Mesh Fabric with high tenacity yarn. with The Active Bio-Synchro mechanism automatically adjusts the tilt tension based on user?s body weight. On reclining, the seat glides backward and provides uninterrupted back support thereby increasing seating comfort.The chair back is ergonomically contoured and has a wide back form. The bio flex lumbar support made from engineered plastic is flexible yet provides firm support to the back. The structural mesh allows free movement of air eliminating odour. As per the direction of engineer-in-charge. | each | 420 | | | 0 | 0 | Yes |
35 | Fabric upholstery, Adjustable Armrests, Knee Tilt Synchro Mechanism, Nylon Pedestal. As per the direction of engineer-in-charge. | each | 162.5 | | | 0 | 0 | Yes |
36 | Half Mesh and Half Fabric Back Upolstery, Adjustable Armrests, Knee Tilt Synchro Mechanism, Nylon Pedestal. As per the direction of engineer-in-charge. | each | 87.5 | | | 0 | 0 | Yes |
37 | HIGH BACK CHAIR WITH SEAT DEPTH ADJUSTMENT- SEAT ASSEMBLY The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 4542 kg/m*,and hardness load 16 + 2 kgf as per 15:7888 for 25% compression.The stitched cover is made from spacer fabric and leatherette Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D), BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.940.03cm x 0.16 +0.0128cm. it upholstered with spacer fabric and leatherette, BACK SIZE : 45 cm. (W) x 75.5 cm. (D), Armrest- The armrest top is moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of @3.8140.03 cm x 0.240.01 cm thk MS E.R.W tube. The armrest height adjustable up fo 6.540.5cm in 5 steps.The Armrest structure is powder coated (DFT 40-60 micron)., Pedestal Assembly- The pedestal is injection moulded ip-biSck\33% giass-filled Nylon 66 and fitted with 5 nos. twin wheel castors. The pedestal | 1205 om. pit h-center dia.(76.1+1.0 cm. With castors.). As per the direction of engineer-in-charge. | each | 87.5 | | | 0 | 0 | Yes |
38 | SEAT/BACK ASSEMBLY: The seat/back are made up of 1.2 +0.1cm. thick hot pressed plywood (measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumbar support for extra comfort. *PCH-7000 HIGH BACKSIZE 56.0 cm. (W) x 88.0 cm. (H) *PCH-7000 SEAT SIZE 56.0 cm. (W) x 49.0 cm. (D), HIGH RESILIENCE " style="color: #0C730F;" ng-if="perItem.filevisibleType == ndaConstantval && perItem.isDownloadPossible == 'Y' && fieldLocal.shortName == 'file_name'">(NDA accepted at }) --> | each | 75 | | | 0 | 0 | Yes |
39 | Half Mesh and Half Fabric Back Upolstery, Adjustable Armrests, Knee Tilt Synchro Mechanism, Nylon Pedestal. As per the direction of engineer-in-charge. | each | 95 | | | 0 | 0 | Yes |
40 | Adj Seat & back Ht, Adj Pu Arms, Bi-Synchro Mechanism, Wishbone? inspired, T- Spine structure, Nylon Pedestal, 5 Position Tilt Limiter. As per the direction of engineer-in-charge. | each | 72.5 | | | 0 | 0 | Yes |
41 | Revolving Chair Made up of Mild Steel Understructure With Leatherette Upholstery with premium net back gives snug feel & superior finish, while the contact-tilt mechanism offers you different adjustments. Use the armrest or shift the seat height to help you obtain maximum comfort.The Poise chair with ergonomic lumbar support rises to the occasion of the challenging task of combining design and function. Its ergonomic back curves along your spine, ensuring your posture does not suffer. As per the direction of engineer-in-charge. | each | 157.5 | | | 0 | 0 | Yes |
42 | Visitor Chair SEAT ASSEMBLY : The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression, Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D), BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette VISITOR TUBULAR FRAME (FU3312): The tubular frame is cantilever type & made of 02.54±0.03 cm x 0.2±0.016 cm thk S.S 202 tube.The back connected to frame through chrome plated high pressure die cast connector piece, Overall Size-60.9W x 64.2 D x 98.2H x 44.8 SH cm. As per the direction of engineer-in-charge. | each | 140 | | | 0 | 0 | Yes |
43 | Chair The seat and back are made up of 1.2cm thick hot pressed plywood, Upholstered with fabric and moulded Polyurethane be Foam together with moulded ABS seat and back covers.. The Back foam is designed with contoured lumber support for extra comport. The back size: 50cm (W) x 49cm (H) and seat size 50cm (W) x 46cm (D). The Tubular Frame is cantilever type & made of dia 2.54cm x 14 BG M.S. E.R.W. tube and black Powder coated. The polyurethane foam is moulded with density= 45+/-2Kg/m3 and hardness =20+/2 kg. on hampden machine at 25% compression. The Armrest is one piece made of black integral skin polyurethane with 50-70 shore ?A? hardness and reinforced with MS insert. . As per the direction of engineer-in-charge. | each | 140 | | | 0 | 0 | Yes |
44 | Chair with SS Understructure SEAT/BACK: The Seat and Back are made up of injection moulded high impact strength PolyPropylene polymer compound with indoor grade UV resistance *SEAT SIZE: 52.5 cm. (W) x 53.2 cm. (D), * BACK SIZE : 51.6 cm. (W) x 40.5 cm. (H) .S.S. UNDERSTRUCTURE: The tubular welded frame is made from Dia 2.22 ± 0.03 cm x O.12 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.12 ± 0.0128 cm Stainless Steel 202 grade tube. The tubes are buff polished to give shiny finish. As per the direction of engineer-in-charge. | each | 157.5 | | | 0 | 0 | Yes |
45 | Sofa Set(3+1+1) Single Seater of Size 840 x 900, Three Seater of size 1900 x 990 mm Upholstery Material: PVC, Burgundy, Thickness : 1 mm Frame- Material : Pine Wood, Moisture content : 10 -12 %, Thickness of Plywood used : 12 mm & 18 mm, Foam : Seat -Material : Slab stock + moulded foam with pocket spring embedded at moulded foam, Density : 28 kg/m3 of slab stock foam and 42 kg/m3. As per the direction of engineer-in-charge. | each | 17.5 | | | 0 | 0 | Yes |
46 | Three Seater Sofa of size Sturdy Solid Wood Construct The sofa frame is made up of plywood that undergoes multi-step treatment for protection against termites and bugs. Horizontal metal stiffeners are added to make the frame more robustTwo Tone Upholstery The PVC upholstery gives the furniture a contemporary appeal. It also helps provide a cool feeling, while you are relaxing. Stainless Steel Legs Stainless Steel Legs enhances aesthetics and prevents the sofa from rusting. Squivel Mechanism In this sofa you will be able to experience a smooth 360 degree clockwise and anti-clockwise rotation while sitting. Elegant Design The sofa displays sharp edges, fillets and angles that give the sofa an elegant touch. The detailed features is indicative of the excellent craftsmanship Opulent Single Seater Sofa of size Sturdy Solid Wood Construct The sofa frame is made up of plywood that undergoes multi-step treatment for protection against termites and bugs. Horizontal metal stiffeners are added to make the frame more robustTwo Tone Upholstery The PVC upholstery gives the furniture a contemporary appeal. It also helps provide a cool feeling, while you are relaxing. Stainless Steel Legs Stainless Steel Legs enhances aesthetics and prevents the sofa from rusting. Squivel Mechanism In this sofa you will be able to experience a smooth 360 degree clockwise and anti-clockwise rotation while sitting. Elegant Design The sofa displays sharp edges, fillets and angles that give the sofa an elegant touch. The detailed features is indicative of the excellent craftsmanship. As per the direction of engineer-in-charge. | each | 17.5 | | | 0 | 0 | Yes |
47 | Coffee Table-Coffee Table of size 1100 W x 600D x 500H mm With a black and glass top base, Glaze coffee table is the perfect center piece for your living room. The table is crafted from an 8 mm tempered glass top and a silver powder coated understructure, which adds resilience to the table. The table also has a 6 mm tempered bottom glass for storing all essentials.. As per the direction of engineer-in-charge. | each | 87.5 | | | 0 | 0 | Yes |
48 | Three seater chair Cross Beam- made of MS ERW rectangular black powder coated Tube of 80 x 40 x 2 mm Leg & arm rest chrome plated made of cold rolled steel. Arm rest & leg assembled to the cross beam with M10 x 100 mm bolts. Seat & back 1.6mm thick powder coated perforated shell of cold rolled MS Sheet. Side Bar of chrome plated solid steel 30 x 12 mm (DIN 174) with flunting & plastic insert .The shell is assembled on the cross beam with help of M8 Bolts The overall dimension is 1608mm (L) x 695mm (H) x 555mm (D), Seat Height : 405mm. As per the direction of engineer-in-charge. | each | 70 | | | 0 | 0 | Yes |
49 | seat shell : the seat shell should be a welded assembly of seat,back and side frame. the seat and back should be made of 0.12±0.013cm thk cr steel sheet with oblong perforations.they should be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should be powder coated ( dft 40-60 microns ). the seat has a front water fall edge to provide popliteal clearance for comfortable seating. it also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. clean and flat surfaces of seat and back aids in easy maintenance. * seat size : 47.8 cm (w) x 44.6 cm (d) * back size : 41.6 cm (w) x 23.0 cm (h) understructure assembly: understructure assembly consshould be ts of connecting beam and leg assembly made of m.s. e.r.w. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.the welded structure assembly should be powder coated ( dft 40-60 microns ).the leg assembly should be fitted with shoes and levellers in nylon. the leg structure should be designed with minimal should be a of contact close to ground providing easy access for cleaning purposes. the shoes fitted to leg assembly help in aligning the structure for back to back arrangements. levellers take cshould be of uneven flooring.connecting beam should be fitted with snap locking end cap.lt also aids in side-by-side understructure alignment arm rest assembly: armrest assembly consshould be ts of armrest frame and armrest pad . the armrest frame should be made up of size 3.175±0.05cm x 0.47±0.027cm thk hr steel and it should be powder coated ( dft 40-60 microns ). armrest pad should be injection molded in nylon and should be fitted onto the armrest frame. The cushions for seat and back should be made up of 1.5 ± 0.1 cm thk foam on a flat MR grade ply 0.8±0.04cm thk and should be upholstered with leatherite As per the direction of engineer-in-charge. | each | 35 | | | 0 | 0 | Yes |
50 | Desk cum bench Scholar combines the elegance of wood with the strength of steel. Its ergonomically designed to minimize fatigue. This Four seater model is best suited for schools and colleges.Dimension-1800 * 895 * 750 (Appx.) Desk panel Seat, Back-The panels are made from 18 mm thk Pre Laminated Boards with PVC edge banding on all sides, Understructure-Made of25.4 x 25.4 mm x1.2 mm thk powder coated ERW tubes at base which are welded to the desk and seat supports that are made of 1.0 mm thk powder coated MS ?C? sections. Stiffeners that are provided between the 2 vertical frames at base and back of seat are made from 25.4 x25.4 x1.2 mm thk powder coated ERW tubes. The tubes are closed with plastic caps. Additional horizontal supports of 1.5 mm thk powder coated MS ?C? sections are placed below the desk and seat to add to the rigidity of the structure. The storage shelf is made from 0.8 mm thk powder coated MS sheet which is affixed below the desktop. Hooks are provided on either sides of the vertical frame of the desk, for hanging bags/bottles. They are made from 6.0 mm dia MS rods. Level adjustors are provided to take care of unevenness in floor. As per the direction of engineer-in-charge. | each | 267.5 | | | 0 | 0 | Yes |
51 | Desk cum bench Scholar combines the elegance of wood with the strength of steel. Its ergonomically designed to minimize fatigue. This three seater model is best suited for schools and colleges.Dimension-1500 * 895 * 750 (Appx.) Desk panel Seat, Back-The panels are made from 18 mm thk Pre Laminated Boards with PVC edge banding on all sides, Understructure-Made of25.4 x 25.4 mm x1.2 mm thk powder coated ERW tubes at base which are welded to the desk and seat supports that are made of 1.0 mm thk powder coated MS ?C? sections. Stiffeners that are provided between the 2 vertical frames at base and back of seat are made from 25.4 x25.4 x1.2 mm thk powder coated ERW tubes. The tubes are closed with plastic caps. Additional horizontal supports of 1.5 mm thk powder coated MS ?C? sections are placed below the desk and seat to add to the rigidity of the structure. The storage shelf is made from 0.8 mm thk powder coated MS sheet which is affixed below the desktop. Hooks are provided on either sides of the vertical frame of the desk, for hanging bags/bottles. They are made from 6.0 mm dia MS rods. Level adjustors are provided to take care of unevenness in floor. As per the direction of engineer-in-charge. | each | 133 | | | 0 | 0 | Yes |
52 | Steel MF System of size 6'x36"x18" with six shelves made of slotted angle Prime quality CRC sheet conforming to IS 513D/10748/5986. The pitches of the slots at 19.05mm, Panels/Shelves : 6 Bend bending process of 905(L) x 448(D) of load capacity 80 Kgs. UDL Max. per shelf, All fasteners of electro perk arised as per IS : 3655 -1985 Painting: All Steel components of powder coated as per IS: 101/1964. As per the direction of engineer-in-charge. | each | 58 | | | 0 | 0 | Yes |
53 | Single Sided Wood & Steel Book Rack- Width: 925mm Main Unit/900mm Add On Unit, Height: 1890mm(Incl. 85mm Skirting)Depth: 300mm, construction- Rigid knockdown construction, Back panel up to the bottom of third rack for additional rigidity.Material- Racks, Back Panel & Skirting: CRCA 0.8mm Thickness Side panels:25mm thk Prelaminated particle board (PLB) with laminate on both sides.Finish- Metal panels: Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). Stackability-The add-on units can be stacked width wise to form a bank of racks having common side panel.Number of Racks- Bottom plus four fixed racks. (Total 5 loading levels). Each rack is provided with stiffener at bottom for strength. Uniformly Distributed Load Capacity per each full shelf is 80 Kg maximum, Label Holder- Label Holder on each main unit to insert labels for identification As per the direction of engineer-in-charge. | each | 65 | | | 0 | 0 | Yes |
54 | Lab Table of Size 4130mm X 1540mm X 900mm Frames - All CFrames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. The C-frame shall also have skirting at back bottom side. Horizontal Members - should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. As per the direction of engineer-in-charge. | each | 87.5 | | | 0 | 0 | Yes |
55 | Notice Board with size 4' X 3' Surface Material-woolen felt / fabric in various colours,Core material-9 mm thick soft board,Backing Material-0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour OR 0.16 to 0.25 mm thick ISI mark GP sheet,Aluminium frame-Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285- 2002 - 16 mm thickness. As per the direction of engineer-in-charge. | each | 35 | | | 0 | 0 | Yes |
56 | Non Magnetic Small White Board 4' x 3'- Surface Material-0.62 to 0.72 mm thick laminate sheet with extra melamine surface,Core material-8 mm thick Particle board,Backing Material-0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour,Aluminium frame-Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285- 2002 - 16 mm thickness. As per the direction of engineer-in-charge. | each | 65 | | | 0 | 0 | Yes |
57 | Lab Stool of circular type 30.0 +/- 0.5 cm and made up of 0.1+/- 0.012 cm thk CR Steel. It is welded to the understructure and black powder coated ( DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure is made of MS tube 2.2 +/- 0.03 cm x 0.16+/- 0.0128 cm thk MS ERW tube. lt is welded ti the MS fabricated circular seat assembly and black powder coated ( DFT 40-60 microns ). The understructure is provided with black PP injection moulded ferrules. As per the direction of engineer-in-charge. | each | 215 | | | 0 | 0 | Yes |
58 | Supply, Installation, Testing, commissioning and handing over of passenger electric traction lift a) Speed-1.00 meter per second b) Stop at all levels. c) Opening-All opening on same side i. Passenger capacity: 08 Passenger/544 Kg ii. Serving floors: GF + 5 Floors. iii. Travel-23.00 Meter (approx) Make- KONE/OTIS/THYSSEN KRUPP | each | 16 | | | 0 | 0 | Yes |
59 | STP-100 KLD CAPACITY Nature of effluent -Domestic Sewage from Kitchen water,W.C, Bathroom Water. Effluent Discharge after Treatment PH-6.5-7.5 BOD (3 days) 10-15mg/liter S.Solids-10-15mg/liter COD -60-80 Oil & Grease -5 mg/Liter Design,Installation,testing & Commisioning of Sewage treatment plant completely for integrated Commercial & Domestic waste capacity 100 cum/MBBR Technology Treated efluent will be used for garding flushing water & soft water purpose & overflow will go to Municipal sewer Comprising of following item.Any other item which the agency envisage for better performence of the plant is requred to be included in the rate. BAR SCREEN-SS-304 fabricated bar screen with 8-12 mm normally placed gaps in screen to allow sewage water flow and prevent higher size debris from entering into the Collection tank at the very entry point it self of the tank,Screen kept inclined at 45 degree to the horizontal with hand track as requried. MS TANKS OF 5 MM MSFRP tanks of requried sizes such as Aeration tank, Tube Settler, No Choice Tank, Sludge Holding, Treated Water Tank. RAW SEWAGE PUMPS -Centrifugal,Non Clogl,Submersible raw sewage pumps to pump sewage from equalization tank to areation tank suitable for handling minimum of 10-12 mm solid particles having a liquid discharge rate of minimum 3 cum /hrs at a head of 10-12 meters suitable for operation on 3 phase 400 voit AC supply Contractor shall ensure submission of detail civil GA Drawings, P & I diagram for the above mentioned component & additional component if so required fcr complete working of the STP. | SET | 1 | | | 0 | 0 | Yes |
60 | Providing and fixing guard rails as per drawing & Technical Specifications and direction of engineer in charge. | meter | 260 | | | 0 | 0 | Yes |
61 | Providing and fixing Litter bins complete as per Technical Specifications and direction of engineer in charge. | No | 26 | | | 0 | 0 | Yes |
62 | Utility ducts in form of 600 mm Ø of NP-4 Pipe across the Project Highway and along with inspection chamber. and direction of engineer in charge. | No | 1259 | | | 0 | 0 | Yes |
63 | Supply of fire buckets 4 No. in each set duly filled with fine sand and fixed on an angle iron frame as per requirement of local authorities. Fire buckets shall be painted red from outside and white from inside with additional handle at the bottom and suitable for outdoor installation. | SET | 4 | | | 0 | 0 | Yes |
64 | Supply and fixing on position the approved Single Line Diagram framed in 1000 x 800 mm size glass frame and installed in main switch room as directed by Engineer Incharge | No | 4 | | | 0 | 0 | Yes |
65 | Design, manufacture, supply, erection, testing & commissioning of following rating of DG Sets in Accoustic Enclosure, having self excited & self regulated 415 V, 3 Phase, 4- Wire, 50 Hz, 0.8 p.f. Alternator coupled with multi-cylinder, turbo-charged/ turbo- charged after cooled as called for, Diesel Engine capable to generate the power not less than the required BHP to achieve the alternator capacity as given below, with radiator Cooled, hospital type silencers and Electronic governer (G3 Governing System), DG set controller suitable for Auto Synchronization & Auto Load Sharing with microproces based Synchronization relay like Woodward/Dief/ Deepsea or equivalent including providing of Engine control panel, 24V batteries of suitable rating, battery-charger with battery leads, inbuilt oil fuel tank of capacity as per OEM standards and complete with all standard accesies & protection as required and as per specifications, including first filling of lube oil, fuel tank, providing common base plate, anti vibration pads, drip trays, foundation bolts, nuts, bolts, cable termination/adopter box sutiable to terminate upto 5 nos. of 3.5Cx300 sq.mm. XLPE cables as required for a complete installation including RCC/PCC foundation for DG set as per the structural detail for Dynamic Load submitted by the Vendor and approve by the Client. DG set should comply relevant Indian standards. DG shall have Remote Monitoring System. 400 KVA (With Acoustic Enclosure) | SET | 1 | | | 0 | 0 | Yes |
66 | Mural painting with good quality paints as per approved size, theme, design, colour, drawing, etc. and at locations directed by the Employer?s Representative. Note: The graffiti/ representative images shown here are indicative only. Contractor shall submit various designs and approved designs (different for different places/locations) shall be executed. | Square meter | 160 | | | 0 | 0 | Yes |
67 | Art work with CNC Machines on granite, marble, sand stone, wood or metals. Art work on granite stone, sand stone, marble stone, solid wood, metals of required thickness as per approved size, theme, design, colour, drawing, etc. and at locations directed by the Employer?s Representative. Note: The graffiti/ representative images shown here are indicative only. Contractor shall submit various designs and approved designs (different for different places/locations) shall be executed | Square meter | 200 | | | 0 | 0 | Yes |
68 | Suppliying and filling good quality cinder in down slab etc. all complete as per building specification and direction of E/I. First floor to third floor | Cubic meter | 388.61 | | | 0 | 0 | Yes |
69 | S/F/F 2 H.P. CROMPTION SUBMERSIBLE PUMP OF ISI MARK WITH STARTER, PANNEL, CABLE, WELL COVER etc. ALL COMPLETE JOB | SET | 8 | | | 0 | 0 | Yes |
70 | Supplying, Installing, Testing, Commissioning of 2.0 T inverter AC including appropriate stabilizer complete setup of Make- (Daikin/Carrier/Hitachi/Voltas or equivalent ) all complete job as per direction of E/I. | each | 360 | | | 0 | 0 | Yes |
71 | Double Ended LT Outdoor Substation and Indoor Switch Gear Room comprising of following major items Gang operated 3-Phase 11Kv, Manually operated outdoor Air Break Switch (AB Switch) Supplying/Receiving, Installation/Erection, Testing and Commissioning of Gang operated 3-Phase 11Kv, 200A 40kA for 1Sec Manually operated Air Break Switch(AB Switch) with Earth Switch to be mounted on two pole structures. | SET | 4 | | | 0 | 0 | Yes |
72 | Providing and fixing of Plain Colour (RAL) finished steel doors made of GPSP (120 GSM Galvanized) sheet; 1.2mm thick for frame and 0.8 mm thick for shutter with shutter thickness of 46mm with SS304 accessories like Ball Bearing Hinges, Mortize Lock, Dore Stopper and Tower Bolt and other necessary items with all complete job. (Make Tata Pravesh, JSW, Shakti Hormann and Jindal) | Square meter | 2945.37 | | | 0 | 0 | Yes |
73 | Bottle Trap 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange | each | 436 | | | 0 | 0 | Yes |
74 | Heavy Duty Wall mounted Liquid Soap Dispenser Silver Colour. Chrome finish | each | 352 | | | 0 | 0 | Yes |
75 | Heavy Duty Towel Ring Round with Round Flange - Chrome finish | each | 256 | | | 0 | 0 | Yes |
76 | Heavy Duty Soap Dish Holder | each | 92 | | | 0 | 0 | Yes |
77 | Heavy Duty Stainless Steel 304 Floor Grating with cockroach trap of 125x125 (mm) size | each | 532 | | | 0 | 0 | Yes |
78 | Heavy Duty Bib Cock with Wall Flange 15 mm nominal bore. | each | 832 | | | 0 | 0 | Yes |
79 | Supplying and erection of a set of cross bracing FRLSame work for 11 KV over head line double pole structure having four members fabricated out of 50 mm X 50 mm X 6 mm angle iron to form a rectangle of minimum size 1400 mm width X 2500 mm height, complete with 50 mm X 6mm M.S. flat iron clamps, bolts and nuts including drilling holes for insulator pins, bolts and nuts etc (as per drawing) and painting with primer and finish paint as required. | SET | 2 | | | 0 | 0 | Yes |
80 | Erection of steel tubular or rail pole strut in cement concrete 1:3:6 (1 cement : 3 coarse Erection of steel tubular or rail pole strut in cement concrete 1:3:6 (1 cement : 3 coarse and refilling and secured with holding clamps, bolts, nuts etc. as required. | each | 2 | | | 0 | 0 | Yes |
81 | Erection of double pole 3 wire cross arm for 11KV/ 22KV/ 33 KV over head lines as required. | each | 6 | | | 0 | 0 | Yes |
82 | Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required. | SET | 12 | | | 0 | 0 | Yes |
83 | Erection of disc/ pin insulator for 11 KV over head lines as required. | SET | 12 | | | 0 | 0 | Yes |
84 | Installation and Commissioning of Display Type LCD, Display Panel Diagonal size (mm) 1778 Width of The Effective Display Area of The Panel (mm) 1539, Height of The Effective Display Area of The Panel (mm) 866, Backlight Technology LED, Display Resolution (Pixels) 1440X1080, Display Brightness (Nits) 329, Touch interface Touch sensitive as well as pen driven,Touch Technology Infrared optical, Number of touch points (Number) 10, Response time (milli seconds) 8, Provision of in built speakers, other peripherals as per technical specifications and as directed by engineer in charge. (Make-Sony/panasonic/LG/Ben-Q/Viewsonic) | each | 8 | | | 0 | 0 | Yes |
85 | Installation and Commissioning of Display Screen size Diagonal 65" 4K Interactive Display dual-pen writing with a 3mm diameter pen tip 2.1 Stereo sound with a built-in woofer Built-in myViewBoard? whiteboarding software to collaborate on the go 4-way split screen content sharing with built-in ViewBoard® Cast software LAN sharing with slot-in PC Built-in RS232 port and vController software for remote control Panel Size 65" Type/Tech TFT LCD Module with DLED Backlight. Display Area (mm) 1431 (H) x 807 (V) (64.5? diagonal) Aspect Ratio 16:9 Native Resolution UHD 3840x2160(Pixels) Colours 1.07B colours (10bit) Brightness 350 nits (typ.) 300 nits (min.) Contrast Ratio 5000:1 (DCR) Response Time 8ms Viewing Angles H = 178, V = 178 typ. Backlight Life 30,000 Hours (Min) Surface Treatment Anti-Glare Bezel Slim rientation Landscape Platform Processor ARM Cortex A73 dual-core 1.2GHz RAM 2GB DDR4 Storage 16GB Touch Type/ Tech IR Recognition Touch Resolution 32767 x 32767 Touch Point 20 points touch, 10 points writing INPUT HDMI 2.0 x3 (3840x2160 @60Hz) RGB / VGA x1 Audio x1 other peripherals as per technical specifications and as directed by engineer in charge. (Make-Sony/panasonic/LG/Ben-Q/Viewsonic) | each | 16 | | | 0 | 0 | Yes |
86 | Supplying,Installing,Testing of Day/night fixed IP Dome Camera with a discreet, dust and IK rated vandal-resistant indoor casing. Varifocal 2.5-10 mm P-Iris lens, remote focus and zoom. Multiple, individually configurable H.264 and Motion JPEG streams; max HDTV 1020P or 2MP resolution at 30 fps. WDR more than 70dB. Video motion detection and active tampering alarm. Memory card slot for optional local video storage. Power over Ethernet. Includes mounting bracket for wall/ceiling or junction boxes as per technical specifications all complete job as per direction of E/I Make- Secure eye/Hikvision//CP Plus. | each | 60 | | | 0 | 0 | Yes |
87 | Supplying,Installing,Testing of Day/night IP Bullet with a discreet, dust and IK rated vandal-resistant indoor casing. Varifocal 2.8-10 mm P-Iris lens, remote focus and zoom. Multiple, individually configurable H.264 and Motion JPEG streams; max HDTV 1020P or 2MP resolution at 30 fps. WDR more than 70dB.Video motion detection and active tampering alarm. Memory card slot for optional local video sorage. Power over Ethernet. Includes mounting bracket for wall/ceiling or junction boxes as per technical specifications all complete job as per direction of E/I Make- Secure eye/Hikvision//CP Plus. | each | 10 | | | 0 | 0 | Yes |
88 | Supplying,Installing,Testing of Multi- Directional Sensor PTZ Camera 5 MP,1/2.3? 5 MP CMOS Sensor with Built-in Automatic IR Cut Filter, 360 ? degrees at all times irrespective of Angle of View32 X Digital Zoom, H.264 and MJPEG, motion detection, Analytics based Pan/ Tilt/ Zoom camera.Built in SD card slot with support upto 64 GB with Class 10 speed, Microphone input support, IP 66, IK10,Axis, ONCAM as per technical specifications all complete job as per direction of E/I Make- Secure eye/ Hikvision/CP Plus. | each | 18 | | | 0 | 0 | Yes |
89 | Supplying,Installing,Testing of All-in-one Video Network recording solution (NVR) for up to 64 channels, Pre-installed, pre-configured IP storage solution with 32 TB storage capacity, RAID-5 protected,Hot-swappable hard drives, Temperature +10 °C to +35 °C, Relative humidity-8 to 90% (non-condensing), CE, UL Certified. Recording shall be calculated for all cameras at full frame rate & resolution for 15 days as per technical specifications all complete job as per direction of E/I Make- Secure eye/Hikvision//CP Plus. | each | 4 | | | 0 | 0 | Yes |
90 | Supplying,Installing,Testing of 42"/43" Full HD LED Professional Display for Monitoring with mounting accessories as per technical specifications all complete job as per direction of E/I (Make- LG/Samsung/ Panasonic/Sony) | each | 16 | | | 0 | 0 | Yes |
91 | Supplying,Installing,Testing of Networking Poe Switch, 10/100/1000 BT ports, 24 ports providing PoE as per 802.3a/f as per technical specifications all complete job as per direction of E/I (Make- D-Link / Cisco/ Panasonic) | each | 20 | | | 0 | 0 | Yes |
92 | Supplying,Installing,Testing of Layer 2 networking switch, 10/100/1000 BT ports, 24 ports providing PoE as technical specifications all complete job as per direction of E/I. (Make- D-Link / Cisco/ Panasonic) | each | 2 | | | 0 | 0 | Yes |
93 | Supplying,Installing,Testing of 1 G SFP Module as per technical specifications all complete job as per direction of E/I. (Make- D-Link / Cisco/ Panasonic) | each | 10 | | | 0 | 0 | Yes |
94 | Supplying,Installing,Testing of KVM Switch 8 Port as per technical specifications all complete job as per direction of E/I. (Make:Digisol / D-Link/Cisco) | each | 5 | | | 0 | 0 | Yes |
95 | Supplying,Installing,Testing of 6 Core Optical Fibre cable in prelaid PVC conduits / pipes / raceway all complete job as per direction of E/I. (Make: Finolex/havells) | Meter | 3000 | | | 0 | 0 | Yes |
96 | Supplying,Installing,Testing of Optical Fibre cable Jointer as per technical specifications all complete job as per direction of E/I | each | 500 | | | 0 | 0 | Yes |
97 | Supply, installation and Testing of Media Convertor as per technical specifications all complete job as per direction of E/I. (Make:Digisol / D-Link/Cisco) | each | 5 | | | 0 | 0 | Yes |
98 | Supplying & installing UTP networking Cat-6 cable suitable for LAN/WAN computer net working as per technical specifications all complete job as per direction of E/I. (Make:Digisol / D-Link/Cisco) | Meter | 2000 | | | 0 | 0 | Yes |
99 | Supplying,Installing,Testing of 42 U Rack for Switches as per technical specifications all complete job as per direction of E/I. (Make:Digisol / D-Link/Cisco) | each | 10 | | | 0 | 0 | Yes |
100 | Supplying,Installing,Testing of 3x3 I/O box with face place Female Rf45 as per technical specifications all complete job as per direction of E/I. (Make:Digisol / D-Link/Cisco) | each | 200 | | | 0 | 0 | Yes |
101 | Supplying,Installing,Testing of CAT 6 Giga Speed 1.2 m Patch Cord as per technical specifications all complete job as per direction of E/I. (Make:Digisol / D-Link/Cisco) | each | 200 | | | 0 | 0 | Yes |
102 | Supplying,Installing,Testing of Command Centre Workstattion with Intel Xeon ProcessorE3-1240 v3 (Quad Core HT, 3.40GHz Turbo, 8MB) or higher, 16 GB Memory or Higher, 6 TB 3.5 inch Serial ATA (7200 rpm) HDD, 16X DVD RW Drive, 1 GB NVIDIA QUADRO K600 Graphic card or higher, Operating System: Windows 10 Professional with1920 x 1080 Display all complete job as per direction of E/I (Make: DELL/HP/ACER) | each | 2 | | | 0 | 0 | Yes |
103 | Supply, installation, testing and commissioning of the following components as required of IP PBX systems,16 S AC, Configration: 8 Trunk Line with 224 Analog Extention all complete job as per direction of E/I. Make:- MATRIX/Dlink./Panasonic | each | 1 | | | 0 | 0 | Yes |
104 | Supply, installation, testing and commissioning of the following components as required of IP PBX systems, 12S AC, Configration :- 110 Analog Extention all complete job as per direction of E/I Make:- MATRIX/Dlink./Panasonic | each | 1 | | | 0 | 0 | Yes |
105 | Supply, installation, testing and commissioning of the following components as required of IP PBX systems, 12S AC, Configration :- 48 Analog Extention all complete job as per direction of E/I Make:- MATRIX/Dlink./Panasonic | each | 2 | | | 0 | 0 | Yes |
106 | Supply, installation, testing and commissioning of Opertor Console all complete job as per direction of E/I Make:- MATRIX/Dlink./Panasonic | each | 2 | | | 0 | 0 | Yes |
107 | Supply, installation, testing and commissioning of DP BOX 100 PAIR all complete job as per direction of E/I | each | 2 | | | 0 | 0 | Yes |
108 | Supply, installation, testing and commissioning of 100 PAIR KRONE BOX all complete job as per direction of E/I | each | 8 | | | 0 | 0 | Yes |
109 | 3C X 1.5 Sqmm Power twisted pair copper cable all complete job as per direction of E/I (Make: Havells) | Meter | 600 | | | 0 | 0 | Yes |
110 | Supply, installation, testing and commissioning of 12 U Networking Rack with Glassdoor all complete job as per direction of E/I (Make:- MATRIX/Dlink./Panasonic) | each | 16 | | | 0 | 0 | Yes |
111 | Supply, installation, testing and commissioning of Telephone Sets (analog and digital) shall be line powered from the system and connected on two wires (single pair) only all complete job as per direction of E/I. Make: BEETEL/ Panasonic/Motorola) | each | 80 | | | 0 | 0 | Yes |
112 | Supply, installation, testing and commissioning of RJ 11 1.2m Patch Cord all complete job as per direction of E/I Make:- MATRIX/Dlink./Panasonic) | each | 100 | | | 0 | 0 | Yes |
113 | Supply, installation, testing and commissioning of 20 KVA Online UPS without Battery, Input 3 Phase Ouput 1 Phase, True Online UPS Systems with input Power factor of 0.99, THDi < 5%, AC-AC efficiency 94 %, Inbuilt isolation transformer covering Online as well as Bypass path having 30 Minutes battery Backup with each UPS System with all accessoriesas as per Eaton. Parllaling Upto 6 Units ( without Synchronization Panel as per oem) Isolation Transformer, Active Input power factor Correction, Input Phase Sequence Corrector shall be inbuild with UPS. Including For 30 Minutes Backup, 32 Nos of 12V 42AH Battery,Racks Links and Interlink DC cable from Battery to UPS and other neccessary accessories all complete job as per direction of E/I. (Make:- APC / MICROTEK / NUMERO ) | each | 2 | | | 0 | 0 | Yes |
114 | Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure). | Cubic meter | 300 | | | 0 | 0 | Yes |
115 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment). | Cubic meter | 300 | | | 0 | 0 | Yes |
116 | Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment). | Cubic meter | 300 | | | 0 | 0 | Yes |
117 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm | Cubic meter | 100 | | | 0 | 0 | Yes |
118 | Fine dressing of the ground. | Square meter | 750 | | | 0 | 0 | Yes |
119 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). | Cubic meter | 100 | | | 0 | 0 | Yes |
120 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge | Cubic meter | 100 | | | 0 | 0 | Yes |
121 | Grassing with selection No. 1 Doob grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and good earth shall be paid for separately). In rows 5 cm apart in both directions | Square meter | 300 | | | 0 | 0 | Yes |
122 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 1.2 m dia and 1.2 m deep | each | 70 | | | 0 | 0 | Yes |
123 | Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge. | each | 70 | | | 0 | 0 | Yes |
124 | Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical ? U ? shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm | each | 200 | | | 0 | 0 | Yes |
125 | Supplying & Fixing of Vertical/Roller Blinds approved Colour & Sample of Make- Vista/Decor all complete job as per direction of EI. | Square meter | 540 | | | 0 | 0 | Yes |
126 | Fixing of Storage type water heater/ Geyser with required accessories like 15 mm CP angle valve on inlet, heavy duty reinforced flexible PVC connector for cold water line and flexible CP brass connector with CP checkout for hot water line, CPVC line connection, MS bracket with two coats of enamel paint, anchor fastners etc to hang the units, providing and fixing of 16 A 3 Pin plug of, etc complete as required. Make- Hindware/ parryware/cera/jaquar as per direction of E/I. Capacity 15 Liters | each | 20 | | | 0 | 0 | Yes |
127 | Providing & Fixing water purifier cum water cooler made of stainless steel having storage capacity of 40 liter & cooling capacity 40 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge . | each | 20 | | | 0 | 0 | Yes |
128 | Supplying and fixing Water Purifier with R.O & U.V :- Water Purifier of 15 Ltr. with with R.O & U.V Technology heavy duty all complete job as per direction of EI. (Make-Aquagaurd/Eureka Forbes /Kent or equivalent ) | each | 10 | | | 0 | 0 | Yes |
129 | Providing and fixing of 9 Watt LED Adjustable Downlighter of make- Havells/ Crompton/ Bajaj/polycab /Phillips or equivalent all complete with necessary fittings and connections all complete job as per direction of EI. | each | 120 | | | 0 | 0 | Yes |
130 | Providing and fixing of 15 Watt LED round Down lighter of make- Havells/ Crompton/ Bajaj/polycab /Phillips or equivalent all complete with necessary fittings and connections all complete job as per direction of EI. | each | 150 | | | 0 | 0 | Yes |
131 | Supplying and fixing 10/15 watt LED type garden light of make- Havells/ Crompton/ Bajaj/polycab /Phillips or equivalent with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc., on pipe post including connection with FR PVC insulated copper conductor cable and earthing the body etc. etc as required all complete job as per direction of EI. | each | 80 | | | 0 | 0 | Yes |
132 | Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required. | each | 144 | | | 0 | 0 | Yes |
133 | Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. | each | 72 | | | 0 | 0 | Yes |
134 | Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. | each | 72 | | | 0 | 0 | Yes |
135 | Supplying, installation, testing & commissioning fire talk back slave station in surface/recess with ptt knob & speaker/microphone enclosed in ms/abs box | each | 72 | | | 0 | 0 | Yes |
136 | Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete. 10 Zone | each | 4 | | | 0 | 0 | Yes |
137 | Supplying, installation, testing & commissioning of main control and indicating panel made out of 16 SWG MS sheet to accommodate the following items duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc complete as required. 10 zone panel for fire alarm system 100 watt amplifier racks suitable for operation on 230V AC/24V DC supply conforming to IEC-268-3 complete with all accessories as required- 2 Nos.(one to act as standby) Talk back master station with LED PTT (press to talk) push button for operation on 230V AC/24 V DC supply conforming to IEC-268 for simplex mode of operation/communication suitable for 20 Nos.talk back unit -1 set. Annoucement control desk suitable for selection of different zones selectively and ON ALL CALL switch with visual indication etc., complete as required- 1 set. Amplifier change over switch for inter changing amplifier- 1 No. Monitor panel for loudspeaker complete output selector ON/OFF switch, fuse visual indications etc. complete as required- 1 No. Gooseneck microphone with stand and ON/OFF switch -1 No. Mains ON/OFF switch, fuse indication lamps, DC and AC voltmeters & ammeters terminal blocks etc. complete as required -1 set. Battery charger trickle cum boost to take complete load of fire alarm & PA system complete with all accessories including providing & fixing of 2 nos. 12 volt,30 AH each sealed maintenance free batteries -1 set. | each | 4 | | | 0 | 0 | Yes |
138 | Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having xlpe insulation ,steel wire armouring & FRLS outer sheath complete as required | Meter | 1600 | | | 0 | 0 | Yes |
139 | Supplying & fixing of 25 mm dia MS flexible pipe with pvc coating and all necessary ancilaries and accessories like coupler as required | Meter | 80 | | | 0 | 0 | Yes |
140 | Providing, storing, handling, shifting, installation, testing and commissioning of portable fire Extinguishers as described below: 6 kg carbon dioxide extinguisher, IS marked, with high pressure discharge tube, horn, control valve, CCE approved cylinder of Make :- ABC/Eco Fire all complete job as per direction of E/I. | each | 10 | | | 0 | 0 | Yes |
141 | Supply, installation and fixing of M.S bucket of 9 liters capacity painted with red oxide paint & lettered as 'Fire' with White and red mounted on freestanding stand, as required including filling with dry sand all complete job as per direction of E/I. | each | 20 | | | 0 | 0 | Yes |
142 | Supply, installation and fixing of First aid box as approved by St.John Ambulance Brigade /Indian Red Cross society conforming to IS : 2217 - 1963 all complete job as per direction of E/I. | each | 30 | | | 0 | 0 | Yes |
143 | Supply, installation and fixing of MS Axe of approved by St.John Ambulance Brigade /Indian Red Cross society conforming to IS : 2217 - 1963 all complete job as per direction of E/I. | each | 20 | | | 0 | 0 | Yes |
144 | Supply, installation and fixing of Shock treatment chart duly mounted on a wooden frame with glass on, as required in 2 languages (Hindi & English) all complete job as per direction of E/I. | each | 20 | | | 0 | 0 | Yes |
145 | Providing and fixing Hand dryer of Make Dolphy/Alpine all complete job as per direction of E/I. | each | 5 | | | 0 | 0 | Yes |
146 | Providing laminated ply wood panelling upto specified height with 1.0 mm lamination mica matt finish of make- Green/Century laminate/ Mika over 6 mm thick ply wood fitted and fixed over hollock wood frame of 25 x 25mm posts at 60 cm centres and 25 x 25mm horizontal members at approx 60 cm centers including cost of anchoring the panelling to walls properly including TW lipping on the top surface as per drawing specification and direction of E/I. | Square meter | 325 | | | 0 | 0 | Yes |
147 | Providing fixing testing and commissioning of cp brass shower mixer with provision of over head shower with 115 mm long bend pipe in built spout ,spout/shower selector with wall flange complete with all accessories as requried and making good the walls wherever required Make- Hindware/ parryware/cera/jaquar as per direction of E/I. | each | 20 | | | 0 | 0 | Yes |
148 | Providing Fixing Saith finish Stainless steel AiSI 316 grade wall mounted coat hook on door complete Make- Hindware/ parryware/cera/jaquar as per direction of E/I. | each | 5 | | | 0 | 0 | Yes |
149 | Providing Fixing hand Shower (Health Fauct) (ABS Body) with 1mtr long Easy Flex Tube in Chrome Finish and wall hook. Make- Hindware/ parryware/cera/jaquar as per direction of E/I. | each | 5 | | | 0 | 0 | Yes |
150 | 12x 6 Feet, Snooker Table, Cherry Colour, covered with Wiraka 777 cloth with 8 Legs(7x7) and Wooden Block Cushion | each | 1 | | | 0 | 0 | Yes |
151 | Natural Wood Frame Club Size Carrom Board With Coins, Striker & Powder 90 cm Carrom Board (Brown) | each | 4 | | | 0 | 0 | Yes |
152 | Full Size Yoga Mat | each | 50 | | | 0 | 0 | Yes |
153 | Synthetic Badminton Court Mat, Water Resistant & Pest Control | Square meter | 330.03 | | | 0 | 0 | Yes |
154 | Table Tennis Board 100mm wheels, 4 Wheels With Lock and 4 Without 20mm x 50mm Frame Dupont Polyurethane Antiglare Paint 25mm Top ITTF Approved | each | 2 | | | 0 | 0 | Yes |
155 | Chess, Lodo, Jigsaw and other small board games. | SET | 2 | | | 0 | 0 | Yes |
156 | Smartrun Dallas 7 HP Peak Treadmill | 15-level Auto-Incline | Max Weight-150kg | Max Speed-20kmph | SET | 10 | | | 0 | 0 | Yes |
157 | Heavy Duty Dumbbell of all sizes and length | SET | 10 | | | 0 | 0 | Yes |
158 | 26 KG Magnetic Aluminium Cast Flywheel Upto 180 KG weight-bearing capacity Foam grip handle with heart rate sensors Large & Non-Slip Footpads Mounted Wheels for Easy movability Gym Trainer Machine | SET | 10 | | | 0 | 0 | Yes |
159 | Smart Bike trainer Floor Space - 1000*510*1165mm Carton Size - L1005*W260*H945mm Flywheel Weight - 16.5lb Max User Weight - 120Kg Max User Height - 6ft 4in | SET | 5 | | | 0 | 0 | Yes |
160 | Marsh Rowing Machine | 8 Level Magnetic Resistance | Max Weight-120kg | SET | 5 | | | 0 | 0 | Yes |
161 | Foldable Water Rower | 16 Level Water Resistance | Max Weight-150kg | SET | 5 | | | 0 | 0 | Yes |
162 | Smartcross Bern Elliptical Cross Trainer with Bluetooth | 2kg Flywheel | Max Weight-120kg | 8 Level Magnetic Resistance | SET | 5 | | | 0 | 0 | Yes |
163 | Provision of Wall décor with Decorative wall paper of requires themes of standard quality selected as per direction of engineer incharge for intire decoration of the block all complete job as per direction of EI. | Square meter | 200 | | | 0 | 0 | Yes |
164 | Providing and installing of copper flower pot having capacity of 1 Cft with pvc decorative plant/flower for interior decoration all complete job as per direction of EI. | each | 40 | | | 0 | 0 | Yes |
165 | Providing and supplying of floor matt of size 4 feet x 2.5 feet of juit finish all complete job as per direction of EI. | each | 20 | | | 0 | 0 | Yes |
| | | | | | | SUM: 0 | |