Item Description 10 passenger lift/1.25 speed /6 floors / 6stops/stainless steel (1.5 mm) car cabin Estimated Cost (Inclusive of GST) |
Item Description 16 passenger lift/1.25 speed /6 floors / 6stops/stainless steel (1.5 mm) car cabin Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. Duly anodised all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by Engineer in Charge. Estimated Cost (Inclusive of GST) |
Item Description Wall Projected 250x210mm, both sides Estimated Cost (Inclusive of GST) |
Item Description Door Mounted, 300x80mm Estimated Cost (Inclusive of GST) |
Item Description Provided and Fixing of Plain Colour (RAL) Finished Steel Door made of GPSP (120 GSM Galvanized) Sheet; 1.2 mm thick for Frame and 0.8mm thick for Shutter with Shutter thickness of 46mm with SS-304 Accessories like Ball Bearing Hinges, Mortize Lock, Door Stopper and Tower Bolt and Other necessary items with all complete job as Per E.I. Estimated Cost (Inclusive of GST) |
Item Description Providing & fixing CP brass 2 way Bib tab of complete including cutting and making good the walls / metalic sheet for WC where required. (15 mm dia.) Estimated Cost (Inclusive of GST) |
Item Description Provding and fixing soil,waste and vent UPVC pipes of 6km per cm2 110 mm dia Pipes Estimated Cost (Inclusive of GST) |
Item Description P.V.C. FITTINGS VENT COWEL - 110 mm dia Estimated Cost (Inclusive of GST) |
Item Description Providing and Fixing 110x110 mm uPVC Floor trap with Height riser/Saddle as required size ftting with seal 50 mm of self cleansing design floor/urinal trap without vent suspended with supporting clamp or in sunken portion including cutting and making good the walls and floors wherever required complete in all respects. 110 mm inlet & 110 mm outlet Long ht Estimated Cost (Inclusive of GST) |
Item Description Providing, fixing, testing and commissioning of pipe inlet fittings fabricated with maximum 3 inlets 40, 50 & 63 mm OD size fixed to 'P' traps including Dripseal/Pipe seal/solvent weld joint/rubber ring joint complete . Estimated Cost (Inclusive of GST) |
Item Description Supplying & installation submersible pumping motor pumpsets ISI marked of approved make Kirloskar, KSB, etc., equivalent, making connection suitable for tube-well/D.C.B. The job includes screwing and welding of flanges on G.I. riser pipes installation, complete fittings accessories with riser pipes jointing of electrical cables other connections making switch board electrical connections, all labour for testing of submersible pump and supply of water to water mains complete in all respects, 2 H.P app. motor having discharging capacity 10 cum/hour against a head of 90 metres. Estimated Cost (Inclusive of GST) |
Item Description Providing, fixing, testing and commissioning of control panel for Terrace Booster pumps . Incoming: MCCB 35A 1 set of Phase indicating lamps, 1 set of 35A Al bus bars, 1No Ammeter, 1No Voltmeter with phase selector switch Feeder for Booster Pumps - 1 No. 1 No. 32A TP MCCB without releases. DOL starter with over load relay, single phase preventor and indicating lamps with ON/OFF push buttons. 1 No. Automanual selector switch. Suitable for booster pumps Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing fire brigade suction hose coupling (draw out connection) with nut for female coupling as per IS-902 complete with 150mm dia. Suction pipe and foot valve (to be connected to static tank) complete as required and as per enclosed specification. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing stainless steel standard fireman's axe with heavy insulated rubber handle tested to 20000 volts as per IS : 926 complete. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing angle iron (40mmx40mmx5mm) door frame and MS sheet (6mm thick) cum glass shutter of size 2.1mtrx0.9mtr(N.S.) with 25mmx25mmx3mm angle frame all around and stiffened in between i/c hinges, handle, locking arrangement, painting with approved synthetic enamel paint i/c sign writing on glass at internal hydrant including providing & fixing S.S. sheet 2mm thick on remaining portion above door to close opening i/c painting etc. as required. Glass shall be 6 mm thick. Estimated Cost (Inclusive of GST) |
Item Description Providing & fixing of MS fire Hose cabinet outdoor type of size 0.75 Mx 0.60 Mx 0.25 M made of 6mm thick MS sheet with 6mm thick glazed glass doors i/c necessary locking arrangement suitable to accomodate 2nos 15m long hoses, one no branch pipe, etc. and mounted on 400 mm height agle . The cabinet shall be painted with red colour shade No. 536 of IS: 5 externally & white internally complete in all respects for internal hydrant and as per enclosed specification. Estimated Cost (Inclusive of GST) |
Item Description Providing & fixing of 25mm dia. gunmetal air release valve with all fittings and forged ball valve on header complete as required and as per enclosed specification. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing following size Pressure gauge (0-15 Kg/Cm2) complete with shut off valve duly calibrated before installation complete as required & as per enclosed specification. 150mm dia. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing reinforced neoprene rubber vibration eliminators/expansion joints (to provide relief from stresses at pipe flanges) suitable for upto 20 kg/cm2 pressure, complete as per specification. Estimated Cost (Inclusive of GST) |
Item Description 150mm dia. Estimated Cost (Inclusive of GST) |
Item Description 80mm dia. Estimated Cost (Inclusive of GST) |
Item Description Providing, fixing, testing & commissioning of MS air cushion tank on top of each riser fabricated from 6mm thick MS plate, 200 mm in diameter and 1.2 m in height with dished ends fabricated from 8mm thick MS plate with Air release valve with stop cock, flanged inlet connection and drain arrangement with 25mm dia valve, pressure gauge with gun metal stop cock complete with all accessories as required and conforming to IS 4736-1968. Estimated Cost (Inclusive of GST) |
Item Description Recommended dia. : 450 Estimated Cost (Inclusive of GST) |
Item Description Height of shell : 2000mm Estimated Cost (Inclusive of GST) |
Item Description Working pressure : 7 Kg/Sq.cm Estimated Cost (Inclusive of GST) |
Item Description Test Pressure : 10 Kg/Sq.cm Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing heavy duty Aluminium armored cables 1.1 KVA grade including necessary support clamps at ceiling level and connection legs complete in all respects. Estimated Cost (Inclusive of GST) |
Item Description Power cable 3 core 16 Sq.mm Estimated Cost (Inclusive of GST) |
Item Description Power cable 3 core 70 Sq.mm Estimated Cost (Inclusive of GST) |
Item Description Supply, installation, testing and commissioning ISI marked (IS:15683) Fire Extinguisher, Carbon-di-oxide type capacity 4.5 Kg. Flat base including valve, discharge hose of not less than 10 mm dia, 1M long and complete in all respects including initial fill with CO2 gas conforming to IS:307-1966 and walll suspension braket as required as per specifications. Estimated Cost (Inclusive of GST) |
Item Description ELECTRICAL PANELS Design,manufacturing,assembling,wiring,supply,installation,testing and commissioning of the following extensible cubicle type indoor mounting,dead front,fully compartementalised with hinged lockable detachable from& backl openable,dust and vermin proof,floor mounting sheet steel clad switchboard fabricated out of 2 mm thick CRCA powder coated sheet steel suitable for use at 415 volt 3 phase 4wire 50 cycle system,BMS Compiatable and to withsatans a symmetrical fault level of below mentioned kA at 415 volt. panels shall be fabricated in easily transportable sections,length,height,depth etc.to match with site condition,complete in all respect. INCOMER:- 1). 1 Nos.160 Amps. TPN MCCB(25 KA) Breaking capacity. 2). 1 Set of RYB phase Indication lamps with suitable rating MCB 3). 1 Set of ON/OFF Indication lamps along with 2A SP MCB backup protecting. 4).1 set Digital Ampere meter with suitable rating CT and selector switch 5). 1 set Digital Volt meter with suitable rating MCBs and selector switch Busbar Electrolytic high conductivity aluminium three phas and neutral busbars rated at 415V, 500 amps,35 kA,insulated with heat shrinkable coloured PVC sleeves & clip on shrounds for joints. The busbar sizing calculations shall be sumitted for approval,considering all derating factors. 3 Nos. 40 Amps. TPN MCCB(16 KA) with electronic releases. Outgoings 1 No.100 amp FP MCCB of 30 kA breaking capacity. (UPS) 1 NO 400 AMP FP MCCB of 30 kA breaking capacity (Rising Main) 1 NO 400 AMP FP MCCB of 30 kA breaking capacity (spare) 1 NO 100 AMP FP MCCB of 30 kA breaking capacity (spare) Estimated Cost (Inclusive of GST) |
Item Description Office Table Size(1200x600x750)mm. Table made of 25mm thk pre lam particle board with edge banding & wire manager. Table top supported with side panel & front panel & Keyaboard Tray. Pedestal Size (400x450Dx725HT)mm. Phenol bond using in Pre-Laminated Particle Board & Edge band thickness will be start from 2mm for Top & 1mm for rest parts. Our PLPB certified from ISI grade & Termite, Borer & Fungus resistance laminated outside in selected color & inside (Non Visible Part) will be balancing white. 100% European design & texture & 100% Product Consistency, fade resistance lamination best International Technology. Color-Maple & Dark Gray . The Product/Company Should be Certified BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC. Estimated Cost (Inclusive of GST) |
Item Description High Back Chair - Chair Size (L) 600mm X (D) 660mm X (H) 1,275mm. Back & seat cover cushion chair uphlostered in fabric. Syncro mechenism with locking system and five star chrome base with nylon casters. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive with task chair & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. The Product/Company Should be Certified BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC. Estimated Cost (Inclusive of GST) |
Item Description Visitor Chair - Chair Size (W)595mm X (D)510mm X (H)875mm. Multi-purpose fixed chair,Metal frame,PU Padding on armrest. Cushion upholstery in leatherette with four leg metal legs with matt finish. The Product/Company Should be Certified BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC. Estimated Cost (Inclusive of GST) |
Item Description Model: Hilton School Desk 2-Seater = 42 nos. Each Floor Size: 1200Wx950Dx760H mm. Providing & supplying fixing of two-seater school desk with shelf/storage under desk which one made by cast iron, desk top made by 18mm thick prelaminated particle board of grade ii type iii of is 12823/latest, two-seater classroom desk cum bench, total size of bench: 1200mm(l)x 950mm(d)x 760mm(h) desk size: 1200mm (w) x 400mm (d) x 760mm (h) bench size: 1200mm (w) x 310mm (d) x 390 / 760mm (h) back size: 1200mm (w) x 150 mm (h), under structure-black 9005 EWR pipe (as per is:7138): 25x25x1.2mm square M.S pipe, of thickness 1.2mm in black epoxy polyester powder coated to the thickness 50-60 microns (+/-5 micron) at base with plastic caps made of pp copolymer (3530 grade) are also provided on the rear frames adding more aesthetic value to the product. Additional horizontal supports of MS. c sections of 1.5mm thick are provided below the desk & seat. Shelf: 0.8mm thick powder coated MS sheet below the desk & hooks on either side of desk in MS rod of Dia 6mm.top, seat and back panel: 18mm thick pre laminated board with machine pressed exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade fixed duly pasted with the assistance of edge banding machine at 200 degree Celsius. Estimated Cost (Inclusive of GST) |
Item Description Model: Teacher Table Size: 1500Wx600Dx750H mm. With Pedestal office desk office desk structure of rectangular shape . Table top 25mm thick table top made of 25mm thick prelaminated particle board work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue . modesty pannel made of 18mm thick, wire management hole with pvc grooment on table top.Construction right side of table top is based on a fixed pedestal 3 drawers & from left side of table top is based on 18mm thk engineered wood pvc edge banding pedestal back,top,bottom & drawers are made of 18mm thick with 1 cpu trolly made in black metal powder coated.fixed pedestal:l:410mm(l)x 580mm(d)x 750mm(h) ,in provided with cetnral lock for security and handles are provided for easy of opening. overall construction of pedestal is 18 mm along with fecia of drawers. three layer prelaminated particles board(wood product) of grade ii type iii of is 12823/latest. The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and an official link/screenshot of the product listing must be provided from www.bifma.org? Estimated Cost (Inclusive of GST) |
Item Description Model: Define, Mesh Chair, Medium Back Chair Dimension: 590Wx630Dx970H mm. fix cantilever chair *The chair made of full mesh in black colour. it will come in matte finish in contemporary style. details: * Arms: pp fixed padded armrest. * Use of ply: 12 mm thick hot pressed BWR plywood (is grade - 303 for seat). * Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat, * Back: frame of design shall be curved made of two pieces injection moulded frame cover with mesh. backrest support adjustable lumbar support * Fixed cantilever chair. * Base: chrome plated tubular frame of cantilever type. The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and an official link/screenshot of the product listing must be provided from www.bifma.org? Estimated Cost (Inclusive of GST) |
Sum(Estimated Cost (Inclusive of GST)): () |