Item Description Supplying all equipments, tools and installation of 1 HP single phase submersible motor pump set of KSB/ ISI make 2900 rpm capable of discharge 5000 LPH at 45 Mtr head with all necessary riser pipe, starter control panel, 1.25" Full way valve, 1.25" M.S clamp, 1.25" G.I Elbow, 1.25" check valve, 1.25" x 9" long G.I Nipple etc. all complete as per direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42. Estimated Cost (Inclusive of GST) |
Item Description Supply, installation, testing and commissioning of sector panel suitable for 6 Zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections and all accessories as required. Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing and Commissioning of smoke detector with builtin LED mounting base complete with all connections etc. as required. Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing and Commissioning of heat detector operating at 54 to 57 deg/C with rate of rise cum fixed tempreature ( dual thermister) type with mounting base complete with all connection etc. as required. Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing and Commissioning of fire alarm sounder with facility to make announcement, mounted in M.S box (16 SWG)with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. Estimated Cost (Inclusive of GST) |
Item Description Supply fixing testing and commissioning of manual call boxes of MS construction in surface/ recess with stainless steel chain and hammer assembly complete with glass and Push Button complete etc. as required. . Estimated Cost (Inclusive of GST) |
Item Description Supply and laying of 2core 1.5 sq mm fire alarm armoured cable 600/1000 volt rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete including connection etc. as required. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing S.S. sliding door bolts (aldrop) with nuts and screws etc. complete:250x16mm Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing SS door latch with necessary screws etc. complete.250x12 mm Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing SS handles "D" type with required fastners (Screws) complete:250x19 mm (Pipe dia) Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing SS hanging floor door stopper with necessary screws etc.complete:150 mm Rubber Stopper Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing SS sliding tower bolt with required fastners (Screws) complete:250x10 mm Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing SS sliding baby latch with required fastners (Screws) complete:100 x 10 mm Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing glazing in aluminium window, ventilator shutters and partions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap bading shall be paid in basic item.)6 mm thick High performance glass Estimated Cost (Inclusive of GST) |
Item Description Painting with Pu anti-corrosive mat finish paint of approved brand and manufacturer to give an even shade: In Steel Work Estimated Cost (Inclusive of GST) |
Item Description Painting with Pu anti-corrosive mat finish paint of approved brand and manufacturer to give an even shadeIn Wood Work Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing dry cladding of Stonelam of 03 mm thk. with machine cut edges of uniform colour and size upto 0.5mx1m, fixed to aluminium frame as per design with the help of Sealent Adheseive , VHB tape, aluminium bracket etc including all as per the specification provided below and Architectural drawing and direction of Engineer-in-Charge.(Aluminium frame work to be paid seperately) Estimated Cost (Inclusive of GST) |
Item Description Providing and supplying Clear toughened glass set of 8 mm Clear toughened Glass + 1.52 Pvb + 6 mm Clear toughened Glass all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge. For payment, only the actual area of gl ass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing Wall & Column Panelling - Finished with Laminate as per design P/F Wall panelling with Seasoned Malaysian Sal Wood Members of the minimum size (nominal) 50mm x 25mm, (a bigger size may be required at the corners, etc)firmly affixed to the supporting wall at a maximum spacing of 450mm x 450mm c/c, (the spacing shall need to be closer, if the room grid so dictates), 12.0 mm thick BWP plywood firmly fixed to the wooden frame, and covered with 1.0mm thick premium quality laminate of the given shade / colour / texture / approved equivalent, in approved pattern. The laminate may have a number of horizontal and vertical grooves / patterns / beadings as per designs and drawings. The Wooden Frame shall be coated with anti-termite paint (Chloropyrophos) as per the Manufacturers Specifications. The panelling shall be at the required distance from the wall, as per instructions of the Project Engineer. All electrical wires, accessories, telephone wires, etc, shall be run in the panelling as per Electrical Drawings and designs. Nothing extra shall be paid for the co-ordination of the same.All items necessary for completing the above mentioned work are deemed to be included in the scope of work, whether or not they are specifically mentioned in the B.O.Q / tender documents / drawings.All exposed wooden surfaces are to be polished and protected with Melamine Polish, and shall be of 1st quality teakwood.All complete as per drawings, designs, specifications and directions of Engineer-in-Charge.Column / Wall Panelling (upto false ceiling ht, with a finishing bead above) Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing Full height Double skin partially glazed partition Providing and fixing double skin partly glazed full height double skin partitions with frames of 50mm x 38mm(finished size) seasoned hardwood members (malaysian salwood / hollock) at max. intervals of 450mm x 450mm with provision of bigger members at skirting, top of partition / top of panelled partition / fixing to false ceiling, fixing to RCC slab, beams etc, fixing to door frames, (door choukhats shall be 1st Class TEAK WOOD ) etc, all woodwork to be treated with 1st quality anti-termite paint, and covered with 12 mm thick BOILING WATER PROOF grade plywood and 1.0mm thick laminate of approved colour, texture and design, as per standard with grooves / small panels cut and pasted in the same as per design, on both sides so as to form a double skin partition, to level 900mm and with 12.0mm edge polished mm clear float glass above, Fixed in wooden frame and with wooden beading as per detail design, which is to be of 1st quality teakwood (All visible wood to be of 1st quality "teakwood") and shall be polished. The wooden frame of the partition shall continue right upto the ceiling, if required, and shall be firmly fixed to the ceiling (and ground) by means of RAWL PLUGS, so as to form a stable system. If the same does not go up to the ceiling, extra supports shall be given to make it a stable system. Estimated Cost (Inclusive of GST) |
Item Description Doors shall have separate choukhats of 100mm x 60mm of Salwood, covered with Teak Ply, and frames of teakwood which shall be of 150mm x 40mm at the top and sides, and 200mm x 40mm at the bottom. Beading shall be given as / design + specs. Door panel shall be of 12mm thick clear glass.All necessary hardware such as stainless steel tower bolts, ISI marked door closers OR floor springs, 6 Lever Godrej Mortice Locks, and any other hardware required for the door shall be included in the price. Any extra members required for Stability of the Partition / Aesthetic value shall be provided without any extra payment for the same. The Wooden Frame and all wooden members / elements shall be coated with anti-termite paint (Chloropyrophos) , as per the Manufacturers Specifications. Door Accessories SpecificationsDoor HandleDoor LatchFloor StopperDoor CloserNote: Payment for doors shall be included in this item / relevant partition item.All items necessary for completing the above mentioned work are deemed to be included in the scope of work, whether or not they are specifically mentioned in the B.O.Q / tender documents / drawings.All electrical wires, accessories, telephone wires, etc, shall be run in the partition as per Electrical Drawings and designs, and the same shall be paid under the Electrical Works to the Electrical Contractor. Nothing extra shall be paid for the co-ordination of the same, or for any minor changes etc. to the Interior Contractor.All exposed wooden surfaces are to be polished, and all exposed wooden surfaces shall be of teakwood. and direction of Engineer-in-charge. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing Fully paneled partitions as per specifications given in Item No. 1 above, except that no glazing shall be there in the partition (doors shall however be glazed, if so desired by the or can be fully panelled also, with the same details and specifications in Item No. 12 ) all complete as per designs, details and specifications. and direction of Engineer-in-charge. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing Low Height Cabinet (2'-6" ht.)for reprographic area andOffice area Providing and fixing Low Height Cabinet with laminated finish, as per description given in furniture items below, all complete with drawers, cabinets, etc., as per drawings and details, vertical and horizontal dividing members to be of 19mm thick bwr blockboard cabinets, cabinet shutters and drawers to be of 19mm thick bwr board, all exposed surfaces to be covered with laminate , all drawers to run on approved quality of drawer slides and all this hardware, and handles to be of approved quality and colour, all complete as per instructions of E/I. (Elevation Area to be measured for payment) Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing Cabinet for Pantry Counter Providing and fixing under counter and overhead Cabinets with laminated finish, all complete , securely fixed to walls with all accessories as per the architectural details , as per instructions of Project Engineer, sufficient to take the load of a fully loaded cabinet with , with shutters, etc., as per drawings and details, vertical and horizontal dividing members to be of 19mm thick bwp blockboard cabinets, all exposed surfaces to be covered with laminate and all hardware,all complete as per instructions of E/I. (Elevation Area to be measured for payment).and direction of Engineer-in-charge. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing a notice board frame to be made of 1st quality hardwood, and infill of 12 mm thick 'Celotex, board, duly covered with "Matte" quality cloth of approved colour and make. Visible surfaces of Frame to be painted with "Premium 1st Quality Paint" in approved colour and shade, and internal frames and internal surface of celotex board to be painted with priming coat. The frame is to be securely fixed to the wall, all complete as per directions fo the Architect / Employer. Size: 5'x3' = 2 Nos.and direction of Engineer-in-charge. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing counter basin size- (mm) 190x550x430 (Jaquar,CAT NO- FLS-wht-5701) including fixing and all accessories as per manufacturers specification and direction of Engineer-in-chargeor equivalent Estimated Cost (Inclusive of GST) |
Item Description Provding and fixing PVC Soil ,Waste & vent pipes all complete110 mm dia Estimated Cost (Inclusive of GST) |
Item Description Provding and fixing PVC Soil ,Waste & vent pipes all complete 40 mm dia Estimated Cost (Inclusive of GST) |
Item Description Providing Paper holder (jaguar AKP-35753PS) or equivalent Estimated Cost (Inclusive of GST) |
Item Description Providing Towel Ring (Jaquar product No. AKP-35751P )or equivalent Estimated Cost (Inclusive of GST) |
Item Description Soap dispenser (jaguar AKP-35735P)or equivalent Estimated Cost (Inclusive of GST) |
Item Description CP brass 2-way bib cock with wall flange(Kubix-F) 15mm(jaguar -KUP-35041PM)or equivalent Estimated Cost (Inclusive of GST) |
Item Description Providing & Fixing 110 mm dia cp jali as Direction of E?I Estimated Cost (Inclusive of GST) |
Item Description Supplying Installing Testing and commissioning of 10 Pair distribution tag box all complete as per specification and direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supplying Installing Testing and commissioning of 20 Pair distribution tag box all complete as per specification and direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supplying Installing Testing and commissioning of 50 Pair distribution tag box all complete as per specification and direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supplying and installation of 10 pair 0.5 sq mm.ATC unarmoured PVC insulated copper conductor telephone cable on surface including connection, testing etc. as required. direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supplying and fixing Two RJ 45 Cat - 6E Lan I/O with Gang box & dual port face plate complete set of D-Link Make including making connection, soldering etc. as required. direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supplying fitting fixing CAT6 U/UTP 24 Port Patch Panel loaded with 24x Toolless RJ 45 complete etc as required .direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supplying CAT6 U/UTP RJ45 Patch Cord 1 Mtr Grey in colour . direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supplying CAT6 U/UTP RJ45 Patch Cord 2 Mtr PVC Grey in colour. (Make: D- Link, Ortronics, Panduit-PANNET) Estimated Cost (Inclusive of GST) |
Item Description Supplying fitting fixing 6U Networking Rack , CRCA steel,CNC programmed punched bended , welded and powder coated with highest quality standred including welded frame ntegrated with side walls and vented top cover with fan mounting provision rear side of the enclosure having wall mounting provision front Glass Door.direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supplying fitting fixing 9U Networking Rack , CRCA steel,CNC programmed punched bended , welded and powder coated with highest quality standred including welded frame ntegrated with side walls and vented top cover with fan mounting provision rear side of the enclosure having wall mounting provision front Glass Doordirection of E/I Estimated Cost (Inclusive of GST) |
Item Description Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ?IS 14609? , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ?IS 15683? ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ?A? ?B? ?C? Class of FIRE complete in all respects (4 Kg Capacity)direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Carbon Di-oxide Type , Gas Confirming to IS ?15222? , Cylinder Confirming to ?IS 7285? & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ?IS 15683? & ?IS 2878? ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ?B? ?C? Class of FIRE (4.5 Kg Capacity)direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ?IS 14609? , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ?IS 15683? ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ?A? ?B? ?C? Class of FIRE complete in all respects (5 Kg Capacity) Estimated Cost (Inclusive of GST) |
Item Description Providing Fixing hand Shower (Health Fauct) (ABS Body) with 1mtr long Easy Flex Tube in Chrome Finish and wall hook. Make- Hindware/ parryware/cera/jaquar as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing CP Bottle Trap for Wash basin and sink. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing CP liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Providing & fixing CP towel ring trapezoidal shape/ rod of 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Providing and fixing S.S soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms Estimated Cost (Inclusive of GST) |
Item Description Providing, fitting & fixing of CP Bib Cock two in one Make- Jaquar/ Cera/ Kohler/Marc all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Providing, fitting & fixing of PVC Floor Trap 110X110 mm dia all complete job as per direction of E/I. Estimated Cost (Inclusive of GST) |
Item Description Supply installation testing & commissioning Roller blind fabric should be made up of 35% Fiberglass, 65% Vinyl on Fiberglass. It should have 3% openness, fabric thickness should be 0.50-0.55 mm, fabric weight should be 478 grams per square meter.Roller Upper Tube: Made of high strength extruded aluminium alloy, finish powder coated with min 60 micron coating, Size of 40 mm outer dia and wall thickness of min. 1.2mm, Special feature, it has end to end groove to hold fabric inside for better strength. Bottom Tube: Made of high strength extruded aluminium alloy, finish powder coated with min 60 micron coating, Size of 20 mm height and wall thickness of min. 1.2mm, Special feature, it has end to end groove to hold fabric inside for better strength. Control Unit: Made of high strength reinforced Nylon grade 6, consisting of outside sleeve and centre shaft, sleeve shall provide bearing surfaceof roller tube and rotate freely on centre shaft, providing smooth quiet and long wearing operations. Brackets: Fixing brackets is made of mild steel with zinc coating, made of thickness of min. 0.7mm. Ball Chain: Made of 2mm thickness polyester cord with moulded 4.5mm round plastic balls. Estimated Cost (Inclusive of GST) |
Item Description Supply installation testing & commissioning of Unmanaged 24 port Gigabit desktop Switch without fiber Module alongwith AC power supply: including necessary connection of CAT 6 UTP cable etc as required. Estimated Cost (Inclusive of GST) |
Item Description Supply installation testing & commissioning of Unmanaged 16 port Gigabit desktop Switch without fiber Module alongwith AC power supply: including necessary connection of CAT 6 UTP cable etc as required. Estimated Cost (Inclusive of GST) |
Item Description Supply installation testing & Commissioning of Media Converter 1000 Mbps RJ 45 to 1000 M Multi mode SC Fiber up 550 Mtr chssis mountable etc as required Make - TP Link Estimated Cost (Inclusive of GST) |
Item Description Supply & laying of 12 core single mode Opitical fibre ITU - G 652 D, all dielectric self supporting armoured underground opitical fibre cable etc as required, opitical fibre cable Estimated Cost (Inclusive of GST) |
Item Description Supplying installation testing & commisioning of Managed 16 port Gigabite Switch including Poe port without fiber Module alongwith AC power supply: including necessary connection of CAT 6 UTP cable etc as required. Estimated Cost (Inclusive of GST) |
Item Description Supply installation testing & commissioning of Indoor IP CCTV IR Dome Camera. 4 MP 1/3'' progressive CMOS,ICR OLux with IR ,2688x1520: 20 fbs , 4mm/F2.0 lens(208/6/8/12 optional) H 264/ MJPEG, dual stream, IP 66 DC 12V & POE DWDR, 3D DNR , BLC, Support on board storage up to 128GB ( SD card not included), 3 axis adjustment, IR range up to 30 m vandal proof housing , Support mobile monitoring via EZVIZ P2P etc as required. Estimated Cost (Inclusive of GST) |
Item Description Supply installation testing & commissioning of Outdoor IP CCTV IR Bullet Camera 4 MP Varifocal 120db WDR1/3" Progressive CMOS, ICR, 0.01lux/F1.2, 2688x1520:20fps, 2.8~12mm VF lens, IP66, H.264/MJPEG, dual-stream, IP66, DC12V & PoE, 120dB WDR, 3D DNR, BLC, IR: up to 30m, Support on-board storage up to 128GB (SD card not included), Support Mobile Monitoring via EZVIZ P2P etc as required Estimated Cost (Inclusive of GST) |
Item Description Supply Installation Testing & Commissioning of Network rack 6U for CCTV survilacne device with complete accessoreis, 1 PDU with 6nos of 5A socket 15 AMP Switch, Fan, wire manager of etc as required. Estimated Cost (Inclusive of GST) |
Item Description Supply Installation Testing & Commissioning of Network Vedio Recorder up to 32 IP camera input, support 4SATA TB Hard Disk up to 24 TB , 2 USB .Max 200 Mbps incoming bandwidth, VGA, HDMI simultaneous vidio outputs, H.265, H.264 dual codec decoding , up to 8 Mp resulution preview and play back,ONVIF Version 2.4 conformane support mobile software and CMS software etc as required Estimated Cost (Inclusive of GST) |
Item Description Supply Installation Testing & Commissioning of 4 TB Seagate Window surveillance Hard Disk etc as required. One for each NVR Estimated Cost (Inclusive of GST) |
Item Description Supply installation testing & commissioning of Network Switch 24 port Poe manged gigabyt 24 # 10/100/1000 Base-T auto-sensing PoE+ ports. 2 dedicated 100/1000 Base-X Fiber SFP ports. Bandwidth: 52 Gbps non-blocking. MAC Address database size: 8,000 media access control (MAC) addresses. Max power (worst case, all ports used, full PoE, line-rate traffic) Estimated Cost (Inclusive of GST) |
Item Description Supply installation testing & commissioning of Network Switch 8 port Poe manged gigabyt 8 # 10/100/1000 Base-T auto-sensing PoE+ ports. 2 dedicated 100/1000 Base-X Fiber SFP ports. Bandwidth: 52 Gbps non-blocking. MAC Address database size: 8,000 media access control (MAC) addresses. Max power (worst case, all ports used, full PoE, line-rate traffic) Estimated Cost (Inclusive of GST) |
Item Description Supply installation testing & Commissioning of 50" Display for CCTV live View & Recording . Screen Size-50" or Higher . Monitor Type-LED. Panel Technology-IPS. Native Resolution-3840*2160 (UHD). Brightness-350cd/m2 or higher. Contrast Ratio-1,100 : 1 or higher. Inputs HDMI, DVI-D, RGB, Stereo Mini Jack, USB. Outputs Stereo Mini Jack, External Speaker Out. External Control-RS232C (In/Out), RJ45, IR Receiver. Estimated Cost (Inclusive of GST) |
Item Description Supply installation testing & Commissioning of Media Converter 1000 Mbps RJ 45 to 1000 M Multi mode SC Fiber up 550 Mtr chssis mountable etc as required Estimated Cost (Inclusive of GST) |
Item Description Supply & laying of 12 core single mode Opitical fibre ITU - G 652 D, all dielectric self supporting armoured underground opitical fibre cable etc as required, Birla.Make opitical fibre cable Estimated Cost (Inclusive of GST) |
Item Description S/I/T/C and final testing of automatic lift complete in the shaft well and pit already constructed as per CPWD specification including automatic ressue device (ADR), All standard equipment, accessories and control equipment as per manufacturer' design and as per CPWD specification (Part III Lifts) onturnkey basis, Conforming to NBC / statutory norms and fulfill following requirments.Type -Passenge lift (13 Passengers)Load - As specified Speed - 1.00 Metre/ secondControl - ACV3F 32 bit microprocessor integrated serial communication control system with RMS ( Remote monitoring system)/ BMS (Building monitoring system) supporting software.Motor/ Machine - Permanent magnetic synchronous gearless motorOperation - Simplex collective selective with/ without lift attendant.Total rise - About 3 metre (approx.) between two stopsLanding - All floors on same sideFloor served - As specified.Signals - Digital car position indicator, car travel direction indicator inside car & at all landings, voice annunciator with suitable music shall be provided in the lift car.Shaft size - As per manufacturer 's design and as per CPWD specification (Part III Lift), Shaft to be constructed seprately.Guide rail - As per manufacturer ' specificationLift & car size - As per manufacturer 's design and as per CPWD specification (Part III Lift), Shaft to be constructed seprately.Car enterance - As per manufacturer 's design and as per CPWD specification (Part III Lift), Shaft to be constructed seprately.Landing enterance - As per manufacturer 's design and as per CPWD specification (Part III Lift), Shaft to be constructed seprately.Car door - SS (stainless steel ) hairline finish centre/ telescopic opening door with vision panel.Landing door - SS (stainless steel ) hairline finish centre/ telescopic opening door with vision panel.Door operation - Automatic electric power operated door, full height infrared curtain with multiple criss/ cross light beam.Car interior - SS (stainless steel ) panel with hairline finish on all sides.Car floor - Anti skid PVC flooring on heavy duty MS (mild steel) platform.Car ceiling & lighting - SS (stainless steel )finish with aesthetic appearance with LED ceiling lights.Car ventilation - Pressure fan/ blower fan ( car fan with automatic sleep timer shall be provided)Emergency lighting in car - Battery operated emergency lighting in the lift car. Estimated Cost (Inclusive of GST) |
Item Description Intercom system -Battery operated intercom system in the lift car,machine room and ground floor/control room.Emergency alarm system -Battery operated alarm bell system in the lift car, ground floor/control room.Position of machine room - Direcly above the hoistway.Electric power supply - AC 415 V , 3 phase ,50 Hz & 230V single phase 50 Hz treminated in machine room.Fire man switch - Fire man switch at machine room/ terminal landing.All car panel buttons and all floor switches must be with braille language as per lift act.Audio visual indication in the lift car showing overloading shall be provided such that doors keep open till excess load is removed.Spring buffer/hydraulic buffer shall be provided.Mechanical over speed governor, door key holes in the floor doors shall be provided.Lift machine hoisting arrangement in the lift machine room and monkey ladder for lift pit should be provided by the lift agency, along wuth the other steel structure works, foundation for the machine etc.In the hoist way fascia plate shall be provided.Permanent wiring in lift machine room and lift well with proper no of light points, with fixtures, exhaust fan, plug points and 3 phase supply shall be made in lift room/shaft by the department or at desired level.Car top safety barricade shall be providedARD (automatic rescue device) - Solid state in built automatic rescue device automatically rescues passengers trapped in the lift car in between floors in the event of power failure, Automatic operation and immediate action in the event of mains failure, capable of moving the lift to the nearest landing, opens the automatic door of the lift car and floor. Sealed maintenance free battery back up with automatic charging unit and autochangeover device on mains failure. (Make Otis/Kone/Schinder /Johnson/Thyssenkrupp) With 3 year free maintaence in DLP Period.as per direction of E/I Estimated Cost (Inclusive of GST) |
Item Description VRV/VRF outdoor AC unit:- Supply installation testing and commissioning of VRV /VRF /MRV outdoor units with following multiple inverter based scroll type compressors, electronic expansion valve, R 410A/ecofriendly green refrigerant, cooling & heating mode both options, special pre-coated fin type heat exchanger, low noise direct driven propeller condenser fans in each module with top discharge including internal wiring, microprocessor controls, safety. The condensing unit should be capable of providing cooling between +/- 5deg. C. to 48 deg. C & heating within 0 deg. C to 15 deg. C, COP not less than 3.3. complete as per specification. Outdoor/indoor units should be of same make (brand). (Single phase/three phase)28 HP Estimated Cost (Inclusive of GST) |
Item Description VRF/VRV indoor AC unit (wall mounted):- Supply installation testing and commissioning of wall mounted indoor split unit comprising of copper evaporator, electronic expansion valve, blower, motor, filter pad, auto air swing louvers, and temperature & on/off display with provision of discharge angle setting by wireless remote controller including internal wiring, controls complete as per specification. (Single phase/three phase)1.33 TR Estimated Cost (Inclusive of GST) |
Item Description VRF/VRV indoor AC unit (ceiling mounted 4 way):- Supply installation testing and commissioning of 4 way round flow ceiling suspended/mounted cassette type unit comprising of copper evaporator, electronic expansion valve, blower, motor, filter pad, auto air swing louvers, temperature &on/off display with inbuilt drain pump & decorative panels including internal wiring, controls. Dimension in terms of length & width should not be more than 950mmX950mm with wireless remote controller. (Single phase/three phase) Estimated Cost (Inclusive of GST) |
Estimated Cost (Inclusive of GST) |
Estimated Cost (Inclusive of GST) |
Item Description Refrigerant:- Supply and additional refrigerant charge of refrigerant R410/410A & equivalent Eco friendly green gas to compensate the additional piping done at site for all systems including testing commissioning as required. Estimated Cost (Inclusive of GST) |
Item Description Drain piping :- Providing and fixing of CPVC, 6Kg/cm2 drain water piping with fittings, support and insulated with 6 mm thick closed cell elastomeric nitrile rubber insulation complete as per specification. Estimated Cost (Inclusive of GST) |
Item Description 20 mm Dia Estimated Cost (Inclusive of GST) |
Item Description 25 mm Dia Estimated Cost (Inclusive of GST) |
Item Description 32 mm Dia Estimated Cost (Inclusive of GST) |
Item Description 40 mm Dia Estimated Cost (Inclusive of GST) |
Item Description Supply and fixing of size 100mmX100mmX100mm PVC Tray with cover for covering of insulated copper pipes of AC. Estimated Cost (Inclusive of GST) |
Item Description Copper piping: - Supply, installation, testing and commissioning of interconnecting copper refrigerant pipe work (19mm/13mm thick) duly insulated with elastomeric nitrile rubber type tubular insulation between indoor & outdoor units as per specifications. And exposed piping should be wrapped with glass woven cloth and lag coating for vapour barrier and weather protection. Joints shall be covered with nitrile rubber tape of 3 mm thick complete as per specification. Estimated Cost (Inclusive of GST) |
Item Description 44 mm O.D. wall thickness more than or equal to 1.4mm (insulation ?19 mm thick) Estimated Cost (Inclusive of GST) |
Item Description 34.9 mm O.D. wall thickness more than or equal to 1.4mm (insulation ?19 mm thick) Estimated Cost (Inclusive of GST) |
Item Description 28.6 mm O.D. wall thickness more than or equal to 1.2mm (insulation ?19 mm thick) Estimated Cost (Inclusive of GST) |
Item Description 22.2 mm O.D. wall thickness more than or equal to 1.0mm (insulation ?19 mm thick) Estimated Cost (Inclusive of GST) |
Item Description 19.1 mm O.D. wall thickness more than or equal to 1.0mm (insulation ?13 mm thick) Estimated Cost (Inclusive of GST) |
Item Description 15.9 mm O.D. wall thickness more than or equal to 0.8mm (insulation ?13 mm thick) Estimated Cost (Inclusive of GST) |
Item Description 12.7 mm O.D. wall thickness more than or equal to 0.8mm (insulation ?13 mm thick) Estimated Cost (Inclusive of GST) |
Item Description 9.5 mm O.D. wall thickness more than or equal to 0.8mm (insulation ?13 mm thick) Estimated Cost (Inclusive of GST) |
Item Description 6.4 mm O.D. wall thickness more than or equal to 0.8mm (insulation ?13 mm thick) Estimated Cost (Inclusive of GST) |
Item Description Flexible connections :- Providing & fixing of flexible canvas connection between indoor unit and duct to avoid the vibration transfer Estimated Cost (Inclusive of GST) |
Item Description Control cable: - Supply and laying, testing & commissioning of following sizes of copper conductor control cables on existing tray including fixing clamps & proper connections to equipment etc. complete as required. Estimated Cost (Inclusive of GST) |
Item Description 4C X 6 sqm Estimated Cost (Inclusive of GST) |
Item Description 4C X 10 sqm Estimated Cost (Inclusive of GST) |
Item Description Outdoor stand fabrication :- Supply, fabrication and erection of angle/channel/flat iron stand, hanging arrangement for air conditioning machines & ducts etc, back /support clamps or other similar work etc. including nut bolts of required size, making holes, fabrication, welding, cutting, etc. and painting with one coat of red oxide paint & two coat of enamel paint as required as per specification. Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning -CUBICAL WORKSTATION SIZE: 1500L+1500X 600DX 1200HT. ·67mm thk Sliding Tile Based Partition. · Single Metal raceway cover at skirting level in Partition.· Pin up & white board in partition above the tabletop.· Table top made of 25mm thk Prelamin particle board with pvc edges. · Tabletop supported with 18mm thk side panel Prelaminated Particle Board with Pvc edge banding side. ·Pedestal of 400Lx 450Dx725 HT (2 drawer + 1filling). .PVC Keyboard Tray . .Metal CPU Trolley. As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning Workstation- Size (1200x600x1200)mm. ·67mm thk Sliding Tile Based Partition.Single Metal raceway cover at skirting level in Partition. Pin up & white board in partition above the tabletop. Table top made of 25mm thk Prelamin particle board with pvc edges. Pedestal of 400Lx 450Dx725 HT (2 drawer + 1filling). PVC Keyboard Tray . Metal CPU Trolley. Phenol bond using in Pre-Laminated Particle Board & Edge band thickness will be start from 2mm for Top & 1mm for rest parts. As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning Mid Back Chair- Chair(L) 590mm X (D) 660mm X (H) 1080mm. Nylon base chair with push back mechanism & Fix handle. Back & seat cover cushion chair uphlostered in fabric & adjustable armrest locks any position. Syncro mechenism with locking system and five star Nylon base with nylon casters. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive with task chair & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning Meeting Table - Confrence Table Size L-2000 X 1200 X750MM. The extendable meeting adds a sense of character to meeting rooms. The innovation modular design enables varius configration. An all wood conference table with minimalist look and basic functionality, ideal for meeting room & top comes with 25mm thik pre lam particle board & side panel 18mm thick prelam particle board & 2mm pvc edge banding with modesty given much needed ptimary and close interaction. Phenol bond using in Pre-Laminated Particle Board & Edge band thickness will be start from 2mm for Top & 1mm for rest parts. Our PLPB certified from ISI grade & Termite, Borer & Fungus resistance laminated outside in selected color & inside (Non Visible Part) will be balancing white. 100% European design & texture & 100% Product Consistency, fade resistance lamination best International Technology. Color-Black Oak. As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning 3 Seater Sofa- Sofa Size( (L)1905mm X (D)890mm X (H)870mm)mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. all plywood used in M R Garde. Color-As per approval .As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning 2 Seater Sofa 2 Seater Sofa Size (1420x870x870)mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning Center Table - Center Table Size (W)1200mm X (D)600mm X (H)450mm. ? Ideal for compact Urban spaces Shelf storage offers generous space for books or magazines Steam Beech wood base makes it highly durable Easy to clean table stays newer for longer Made from sustainably sourced Beech wood. As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning Center Table Side Table - Side Table Size (W)600mm X (D)400mm X (H)500mm ? Ideal for compact Urban spaces Shelf storage offers generous space for books or magazines Steam Beech wood base makes it highly durable Easy to clean table stays newer for longer Made from sustainably sourced Beech wood. As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning Training Desklet Chair - Chair Size (W)580mm X (D)760mm X (H)930mm. ? Timeless modern design that elevates your office space Medium back support provides comfortable sitting experienceBreathable premium soft fabric upholstery is easy to maintainThe chrome plated 4-legs cantilever base esures stability. Cushioned curved backrest and PU foam cushioned seat gives you a comfortable sitting experience ? Fixed armrests with removable half writing pad transforms the chair into your study nook. ? As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning Training Office Table with Side Unit - Table Size 1800LX 900DX 750HT · Table top made of 36mm thk Prelamin particle board with pvc edges. · Table top made of 36mm thk Prelamin particle board with pvc edges. · Tabletop supported with 25mm thk side panel & 18 mm thk Modesty Panel in Prelaminated Particle Board with Pvc edge banding side. ·Pedestal of 400Lx 450Dx600 HT (2 drawer + 1filling). As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning Training Table with Side Table- Table-SIZE: 1800mm(L) x 900mm(W) x 750mm(H) Side unit size: 900mm(L) x 400mm(W) x 750mm(H).Table-25mm thk. Prelam Particle board tabletop with PVC edge banding.Tabletop Supported with 25mm thk Prelam Particle board Side and 18mm thick Modesty panel with PVC edge banding.PVC Keyboard tray & Metal CPU trolley with castors.Side unit top made of 25mm thk. Prelam Particle board with PVC edge banding. 18mm thk Prelam Particle board side , Shelves & Openable shutter with PVC edge banding. Back in 9mm thk Prelam Particle board. Hardware included (i.e. Hinges , Handle & Lock).As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning Back Unit - Size (L)1500mm X (D)450mm X (H)740mm.with 4 door. The unit is built from sturdy board encased finished with a Chesswood finish within its well-proportioned shelves. Consisting of three shelves there is adequate space. Color- Chesswood.As per Direction of E/I Estimated Cost (Inclusive of GST) |
Item Description Supply, Installation, Testing, commissioning High Back Chair 360° Degre Revolving Chair* All Over Size Is : 590mm(l)x 505mm(d)x 1280mm(h) ,*the Chair Made Of Full Leatherette In Black Colour . It Will Comes In Matte Black Finish Finsih In Contemporary Style .Details : Arms : Chrome Finish Arms With Pu Padding .* Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (is Grade - 303 For Seat And Back) .* Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back . Backrest Support Foam Design Based On Symmetrical Lumbar Support.* Mechanism : Knee Tilt Mechanism .* Only Seat Size Is 505mm(l)x 505mm(d)x 610mm(h) & The Back Size Is 590mm(l)x 710mm(h). Seat Maximum Height Is 610mm & Minimum Height Is 510mm & Back Height From Floor Maximum Height Is 1280mm & Minimum Height Is 1180mm.* Gas Lift 100 Mm Telescopic Haudraulic * Base : 650 Mm Chrome Base With Smooth Castors . Estimated Cost (Inclusive of GST) |
Item Description "Supply, Installation, Testing, commissioning Office Primium Visitor Chair- Fix Cantilever Chair. All Over Size Is : 610mm(l)x 505mm(d)x 990mm(h) ,*the Chair Made Of Full Leatherette In Black Colour .It Will Comes In Matte Black Finish Finsih In Contemporary Style .Details :* Arms : Chrome Finish Arms With Pu Padding .* Use Of Ply: 12 Mm Thick Hot Pressed Bwr Plywood (is Grade - 303 For Seat And Back) .* Seat: 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Seat , * Back : 40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In Back . Backrest Support Foam Design Based On Symmetrical Lumbar Supportbackrest Support.* Only Seat Size Is 610mm(l)x 505mm(d)x 485mm(h) & As per Direction of E/I Estimated Cost (Inclusive of GST) |
Sum(Estimated Cost (Inclusive of GST)): () |