| S No |
Item Description |
Item Long Description |
Quantity |
Unit |
Group No. |
ITM000910479
43
1 |
1 |
Supplying, installation, testing and commissioning of electric driven main fire pump suitable for automatic operation and consisting of following complete in all respect as required a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 Kg / sq.cm. at highest and farthest outlet at specified flow of 4560 lpm at 100 Mtr. head conforming to IS 1520 b) Suitable HP SQ cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415Volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class- F insulation, conforming to IS- 325 c) M.S. Fabricated common base plate, coupling, coupling guard, foundation bolts etc as required. d) Suitable cement concrete foundation duly plastered with anti vibration pads. Makes of Pumps: Kirloskar / Mather&Platt. Makes of Motors: Siemens/ ABB/ Kirloskar PUMP HP Calculated :150 |
1.000 |
Set |
NA |
ITM000910480
43
2 |
2 |
Supplying , installation, Testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following : complete in all respect as required. Note: Please find the detailed Scope of Work for further description of item. |
1.000 |
Set |
NA |
ITM000910481
43
3 |
3 |
Supplying , installation , testing and commissioning of electric driven pressurisation / Jockey pump suitable for automatic operation and consisting of following : complete in all respect as required a) Horizontal type, multistage, centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal and flow of 460 lpm at 100 Mtr head conforming to IS 1520 b) Suitable HP SQ cage induction motor TEFC type suitable for operation on 415Volts, 3 phase 50 Hz. AC with IP 55 class of protection for enclosure, horizontal foot mounted type with Class- F insulation, conforming to IS-325 c) M.S. Fabricated common base plate, coupling, coupling guard, foundation bolts etc as required. d) Suitable cement concrete foundation duly plastered with anti vibration pads. Makes of Pumps : Kirloskar / Mather&Platt Makes of Motors : Siemens/ ABB/ Kirloskar PUMP HP Calculated :20 |
1.000 |
Set |
NA |
ITM000910482
43
4 |
4 |
Fabricating, Supply, installation, testing and commissioning of Motor control center suitable for the operation of Jockey,Main motor driven and Diesel Engine pumps of relevant rating with required ammeter, voltmeter,busbar and individual Auto - Manual selector switchs with etc including nesessary cabling and earthing from the panel to the motors with required fittings. Electrical pump-01 (4560 lpm, Head-100m,power-150 HP) Jockey pump-01 (460 lpm,Head-100m,Power-20 HP). Note: Please find the detailed Scope of Work for further description of item. |
1.000 |
Set |
NA |
ITM000910483
31
5 |
5 |
Supply of 16 Sqmm 4 Core XLPE insulated, 1100V grade armoured aluminium cable as per specification confirming to IS:7098 (Part -I). For Jockey pump Makes : Torrent / Universal / Unicab / Polycab / Havells / Gloster / KEI. |
25.000 |
Metre |
NA |
ITM000910484
31
6 |
6.1 |
Supplying, laying, testing & commissioning of FRLS,PVC outer sheathe, steel armoured, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The rate shall excludes tray & Hume pipes. The minimum size of the cables shall as mentioned below, 2R x 3.5C X 150 Sq.mm XLPE Al.Ar Cable for main panel to Fire pump room |
460.000 |
Metre |
NA |
ITM000910490
31
7 |
6.2 |
Supplying, laying, testing & commissioning of FRLS,PVC outer sheathe, steel armoured, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The rate shall excludes tray & Hume pipes. The minimum size of the cables shall as mentioned below, 2R x 3C X 120 Sq.mm XLPE Al.Ar for main pump |
50.000 |
Metre |
NA |
ITM000910491
31
8 |
6.3 |
Supplying, laying, testing & commissioning of FRLS,PVC outer sheathe, steel armoured, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The rate shall excludes tray & Hume pipes. The minimum size of the cables shall as mentioned below, 12C X2.5 Sq.mm for Diesel Engine |
25.000 |
Metre |
NA |
ITM000910492
31
9 |
6.4 |
Supplying, laying, testing & commissioning of FRLS,PVC outer sheathe, steel armoured, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The rate shall excludes tray & Hume pipes. The minimum size of the cables shall as mentioned below, 2C X 2.5 Sq.mm for for Instrumentation |
60.000 |
Metre |
NA |
ITM000910495
31
10 |
6.5 |
Supplying, laying, testing & commissioning of FRLS,PVC outer sheathe, steel armoured, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The rate shall excludes tray & Hume pipes. The minimum size of the cables shall as mentioned below, 3 C X 4.0 Sq.mm for Start /Stop push button |
30.000 |
Metre |
NA |
ITM000910496
31
11 |
6.6 |
Supplying, laying, testing & commissioning of FRLS,PVC outer sheathe, steel armoured, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The rate shall excludes tray & Hume pipes. The minimum size of the cables shall as mentioned below, 4 C X 6.0 Sq.mm Cu.cable for Pump room DB |
30.000 |
Metre |
NA |
ITM000910498
31
12 |
6.7 |
Supplying, laying, testing & commissioning of FRLS,PVC outer sheathe, steel armoured, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The rate shall excludes tray & Hume pipes. The minimum size of the cables shall as mentioned below, 4 C X 4.0 Sq.mm Cu.cable for Operator room DB |
60.000 |
Metre |
NA |
ITM000910512
31
13 |
7 |
Supply and Installation of 300mm x 50mm x 2mm thick GI perforated cable tray with cover along with required angle supports, with coupler plates, Anchor bolts and nuts etc complete and the tray should be fitted on the wall / Ceiling etc. complete. |
30.000 |
Metre |
NA |
ITM000910513
31
14 |
8 |
G.I. Earthling strips of 25mm x 6mm thick, strip shall be run on floor / ceiling / walls, from the equipment to the nearest Earth pit with necessary accessories as required. (Earth pit shall be executed by other agencies). |
50.000 |
Metre |
NA |
ITM000910514
31
15 |
9.1 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 250mm nominal dia C Class |
6.000 |
Metre |
NA |
ITM000910515
31
16 |
9.2 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 200mm nominal dia C Class |
30.000 |
Metre |
NA |
ITM000910516
31
17 |
9.3 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 150mm nominal dia C Class |
30.000 |
Metre |
NA |
ITM000910517
31
18 |
9.4 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 100mm nominal dia C Class |
30.000 |
Metre |
NA |
ITM000910518
31
19 |
9.5 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 80mm nominal dia C Class |
20.000 |
Metre |
NA |
ITM000910519
31
20 |
9.6 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 50mm nominal dia C Class |
30.000 |
Metre |
NA |
ITM000910520
47
21 |
10.1 |
Providing, installation, testing and commissioning of dual plate non - return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc as required Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 200 mm.dia |
3.000 |
Each |
NA |
ITM000910521
47
22 |
10.2 |
Providing, installation, testing and commissioning of dual plate non - return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc as required Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 100 mm. dia |
1.000 |
Each |
NA |
ITM000910526
47
23 |
10.3 |
Providing, installation, testing and commissioning of dual plate non - return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc as required Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 80 mm .dia |
1.000 |
Each |
NA |
ITM000910527
47
24 |
10.4 |
Providing, installation, testing and commissioning of dual plate non - return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc as required Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 50 mm .dia |
1.000 |
Each |
NA |
ITM000910528
47
25 |
11.1 |
Supply , fixing , testing and commissioning of butterfly valve PN 16, with Bronze / Gun metal seat duly ISI marked complete with Nuts, Bolts, Washers, gaskets, conforming to IS 13095 of following sizes as required. Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 250 mm. dia |
3.000 |
Each |
NA |
ITM000910529
47
26 |
11.2 |
Supply , fixing , testing and commissioning of butterfly valve PN 16, with Bronze / Gun metal seat duly ISI marked complete with Nuts, Bolts, Washers, gaskets, conforming to IS 13095 of following sizes as required. Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 200 mm. dia |
3.000 |
Each |
NA |
ITM000910530
47
27 |
11.3 |
Supply , fixing , testing and commissioning of butterfly valve PN 16, with Bronze / Gun metal seat duly ISI marked complete with Nuts, Bolts, Washers, gaskets, conforming to IS 13095 of following sizes as required. Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 150 mm .dia |
15.000 |
Each |
NA |
ITM000910531
47
28 |
11.4 |
Supply , fixing , testing and commissioning of butterfly valve PN 16, with Bronze / Gun metal seat duly ISI marked complete with Nuts, Bolts, Washers, gaskets, conforming to IS 13095 of following sizes as required. Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 100 mm .dia |
3.000 |
Each |
NA |
ITM000910532
47
29 |
11.5 |
Supply , fixing , testing and commissioning of butterfly valve PN 16, with Bronze / Gun metal seat duly ISI marked complete with Nuts, Bolts, Washers, gaskets, conforming to IS 13095 of following sizes as required. Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 80 mm. dia |
2.000 |
Each |
NA |
ITM000910533
47
30 |
12.1 |
Supplying, installing and commissioning C.I. flanged Y type Strainer with SS mesh, suitable flanges, nuts, bolts, gaskets etc. complete. Make:PORTER/ZOLOTO/LEADER/ SARKAR 250mm dia. |
2.000 |
Each |
NA |
ITM000910536
3
31 |
13 |
Supply, installation, testing and commissioning of Bourden type, stainless steel dial type pressure gauge with isolation valve and pipe calibration of 0-16 kg/cm2. MAKE: HGURU / FIEBIG and Approved makes |
4.000 |
Numbers |
NA |
ITM000910537
3
32 |
14 |
Supply and installation of Pressure switches in the MS pipe including connection etc as required. Makes: Danfoss/ Indfoss / Approved |
4.000 |
Numbers |
NA |
ITM000910538
3
33 |
15 |
Supply and installation of Flow switches in the MS 150 pipe including connection etc as required. Makes:Sytem Sensor/ Switzer / Approved |
4.000 |
Numbers |
NA |
ITM000910539
3
34 |
16 |
Supplying, installing, testing and commissioning of 25mm Ball valves Makes: Leader/ Zolotto / Approved |
4.000 |
Numbers |
NA |
ITM000910549
31
35 |
17.1 |
Exhaust pipe for Diesel engine of 150 mm dia M.S. Medium grade with mineral wool insulation with aluminum sheet. a.150 mm dia M.S. Medium grade with mineral wool insulation with aluminum sheeting. |
20.000 |
Metre |
NA |
ITM000910955
31
36 |
17.2 |
Exhaust pipe for Diesel engine of 150 mm dia M.S. Medium grade with mineral wool insulation with aluminum sheet. b.150mm dia M.S. Medium grade shall be laid above ground |
5.000 |
Metre |
NA |
ITM000910956
3
37 |
18 |
Supply and commissioning valve chamber size 450 x 750 x 450 deep in CM 1;4 over a bed of 100mm PCC 1:4:8 with inside and outside plastered smooth in CM 1:4 12mm thick. Supply and fixing of R.C.C. frame and cover. |
1.000 |
Numbers |
NA |
ITM000910958
3
38 |
19 |
Supply ,erection,testing and commissing of Flow Meter and Pipeline 150mm dia including necessary fittings etc.complete.( INTERNAL PUMP ROOM TEST LINE ) |
4.000 |
Numbers |
NA |
ITM000910959
3
39 |
20 |
Supply and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25mm dia Gun metal wheel valve, with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. |
1.000 |
Numbers |
NA |
ITM000910960
3
40 |
21 |
Supply, installation, testing and commissioning of 25 / 20mm dia Air Release Valve |
2.000 |
Numbers |
NA |
ITM000910961
3
41 |
22 |
Supply, installation, testing and commissioning of 100mm dia Water Level Controller with 2 Port Solenoid Valve (2 Way Valve) including float and motorised valve and suitable power cable |
1.000 |
Numbers |
NA |
ITM000910963
31
42 |
23.1 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 200mm nominal dia C Class |
25.000 |
Metre |
NA |
ITM000910964
31
43 |
23.2 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 150mm nominal dia C Class |
1050.000 |
Metre |
NA |
ITM000910966
31
44 |
23.3 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 125mm nominal dia C Class |
1570.000 |
Metre |
NA |
ITM000910968
31
45 |
23.4 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 100mm nominal dia C Class |
1310.000 |
Metre |
NA |
ITM000910969
31
46 |
23.5 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 80mm nominal dia C Class |
120.000 |
Metre |
NA |
ITM000910970
31
47 |
23.6 |
Providing , laying, testing & Commissioning of following classes MS pipes conforming to IS 3589 and 1239 including fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : Jindal / Hissar / Tata pipes 50mm nominal dia C Class |
80.000 |
Metre |
NA |
ITM000910974
3
48 |
24.1 |
Supply , fixing , testing and commissioning of butterfly valve PN 16, with Bronze / Gun metal seat duly ISI marked complete with Nuts, Bolts, Washers, gaskets, conforming to IS 13095 of following sizes as required. Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 150 mm .dia |
5.000 |
Numbers |
NA |
ITM000910977
3
49 |
24.2 |
Supply , fixing , testing and commissioning of butterfly valve PN 16, with Bronze / Gun metal seat duly ISI marked complete with Nuts, Bolts, Washers, gaskets, conforming to IS 13095 of following sizes as required. Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 125 mm .dia |
4.000 |
Numbers |
NA |
ITM000910980
3
50 |
24.3 |
Supply , fixing , testing and commissioning of butterfly valve PN 16, with Bronze / Gun metal seat duly ISI marked complete with Nuts, Bolts, Washers, gaskets, conforming to IS 13095 of following sizes as required. Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 100 mm dia |
3.000 |
Numbers |
NA |
ITM000910982
3
51 |
24.4 |
Supply , fixing , testing and commissioning of butterfly valve PN 16, with Bronze / Gun metal seat duly ISI marked complete with Nuts, Bolts, Washers, gaskets, conforming to IS 13095 of following sizes as required. Makes: Audco / Kirloskar / BDK / H- Shankar / Leader/ Zolotto / Intervalve. 80 mm dia |
5.000 |
Numbers |
NA |
ITM000910988
23
52 |
25.1 |
Painting with synthetic Fire RED enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work including Applying 2 priming coats with primer of approved brand and manufacture, low VOC (Volatile Organic Compound ) content.With ready mixed red oxide zinc chromatic on steel / iron works VOC content less than 250 grams/ litre Material and labour for 2 coat of primer and 2 coat of Synthetic enamel FIRE RED color painting |
1700.000 |
Sq.Metr |
NA |
ITM000910991
3
53 |
26 |
Supply and fixing 4 way fire brigade connection of cast iron body with 4 Nos Gun metal Male instantaneous inlet couplings complete with cap and chain as required for 150mm dia MS pipe connection, conforming to IS 904 as required. Make: Mini Max / Safex / Newage / Winco /Padmini. |
1.000 |
Numbers |
NA |
ITM000910993
3
54 |
27 |
Supply and fixing 2 way fire brigade /SIAMESE CONNECTION of cast iron body with 2 Nos Gun metal Male instantaneous inlet couplings complete with cap and chain as required for 100mm dia MS pipe connection, conforming to IS 904 as required. Make: Mini Max / Safex / Newage / Winco /Padmini. |
1.000 |
Numbers |
NA |
ITM000910998
3
55 |
28 |
Supplying and fixing single headed Internal / External hydrant valve with instantaneous Gun metal/SS couplings of 63mm dia with Cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gun Metal cap and chain as required Make: Mini Max / Safex / Newage / Winco / Padmini. |
71.000 |
Numbers |
NA |
ITM000910999
3
56 |
29 |
Supplying and fixing Double headed Internal / External hydrant valve with instantaneous Gun metal couplings of 63mm dia with Cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gun Metal cap and chain as required Make: Mini Max / Safex / Newage / Winco / Padmini. |
6.000 |
Numbers |
NA |
ITM000911000
3
57 |
30 |
Supplying and fixing 63mm dia, 15 mtr long CP hose pipe with 63mm dia Male and Female Gun metal / SS couplings duly binded with GI wire, rivets etc conforming to IS 636 (Type -A) as required. Make: Mini Max / Safex / Newage / Winco /Padmini. |
144.000 |
Numbers |
NA |
ITM000911001
3
58 |
31 |
Supplying and fixing of hose cabinet of size 750mm X 600mm x 250mm made of No 16 gauge SWG CRCA sheet with 6mm thick glazed glass door including necessary locking arrangement suitable to accommodate 2 Nos 15 mtr long Hose pipe, 1 No branch pipe, mounted on wall OR raised brick platform and duly painted with Post office red externally and white internally wit Make: Mini Max / Safex / Newage / Winco /Padmini. |
12.000 |
Numbers |
NA |
ITM000911002
3
59 |
32 |
Supplying and Providing of 2 No s of Mechanical Foam 20 litrs TIN with Foam making branchpipe - FB10X Made of Aluminium Alloy. 2.1/2 male Instantaneous inlet, 450 LPM, foam-water solution capacity at 7kg/cm2,Inlet Pressure 7 bar,Working range 22meters, With delivery hose 2 nos of 15 m length including necessary Covered shed dimensions:2.5m x2.0mx 2.0m Height with doors lock arrangement suitable to accommodate . Make: Omex ,Sainath Fire/ Equivalent. |
4.000 |
Numbers |
NA |
ITM000911003
3
60 |
33 |
Supplying , Installing , testing and commissioning of Fire Monitor comprising of 3 (80mm) and 6 (152mm) diameter waterways are designed for applications that require large volumes of water with minimal manpower or friction loss. Large volume streams are ideally suited for breaking through thermal updrafts on tank fires, covering large areas quickly for vapor recovery, and for fireboat applications. Monitors can also be furnished with manifolds that are custom-built for specific requirements with Storz Quick Connect Nozzle 3 (80mm), 5 (127mm), or 6 (152mm) as required. |
5.000 |
Numbers |
NA |
ITM000911004
29
61 |
34 |
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (Supplying , fabricating, structural steel supports such as MS channels, angles, flats , rods as required at site with anchor fasteners, clamps, threaded rods, nuts, bolts, washers etc. complete). |
5500.000 |
K.G.s |
NA |
ITM000911005
3
62 |
35 |
Supply and installation of Pipe Wash out arrangement MS Elbow,Butterfly Valve-80 mm dia, end Plug details as per Installation detail drawing and main drawing shown locations. |
3.000 |
Numbers |
NA |
ITM000911006
23
63 |
36.1 |
Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : bituminous road |
100.000 |
Sq.Metr |
NA |
ITM000911007
23
64 |
36.1 |
Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : bituminous road |
100.000 |
Sq.Metr |
NA |
ITM000911008
25
65 |
37.1 |
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
15.000 |
Cu. Metr |
NA |
ITM000911010
25
66 |
38.1 |
Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : In cement mortar |
21.000 |
Cu. Metr |
NA |
ITM000911011
51
67 |
39.1 |
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
155.000 |
Cu. mm |
NA |
ITM000911012
25
68 |
40.1 |
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavatedearth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. Ordinary rock |
24.000 |
Cu. Metr |
NA |
ITM000911014
25
69 |
40.2 |
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavatedearth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. Hard rock (blasting prohibited) |
16.000 |
Cu. Metr |
NA |
ITM000911051
31
70 |
41.1.1 |
Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
450.000 |
Metre |
NA |
ITM000911053
31
71 |
41.1.2 |
Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil. Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm |
10.000 |
Metre |
NA |
ITM000911056
31
72 |
42.1.1 |
Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m : Ordinary rock : Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia |
70.000 |
Metre |
NA |
ITM000911057
31
73 |
42.2.1 |
Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m : Hard rock (blasting prohibited) Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia |
15.000 |
Metre |
NA |
ITM000911059
31
74 |
43.1 |
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. |
120.000 |
Metre |
NA |
ITM000911061
31
75 |
43.2 |
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 450 mm dia. |
10.000 |
Metre |
NA |
ITM000911065
31
76 |
44.1 |
Supplying and wrapping the anticorrosive material for buried pipes with coating of Primer and wrapping with 4 mm thick polymer corrosion resistant tape as per IS : 10221 with 15 mm overlap etc.complete and as directed by engineer in charge 150 mm nominal dia |
120.000 |
Metre |
NA |
ITM000911072
31
77 |
44.2 |
Supplying and wrapping the anticorrosive material for buried pipes with coating of Primer and wrapping with 4 mm thick polymer corrosion resistant tape as per IS : 10221 with 15 mm overlap etc.complete and as directed by engineer in charge 125 mm nominal dia |
120.000 |
Metre |
NA |
ITM000911073
31
78 |
44.3 |
Supplying and wrapping the anticorrosive material for buried pipes with coating of Primer and wrapping with 4 mm thick polymer corrosion resistant tape as per IS : 10221 with 15 mm overlap etc.complete and as directed by engineer in charge 100 mm nominal dia |
120.000 |
Metre |
NA |
ITM000911074
25
79 |
45.1 |
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
5.000 |
Cu. Metr |
NA |
ITM000911075
23
80 |
46.1 |
12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) |
740.000 |
Sq.Metr |
NA |
ITM000911076
25
81 |
47.1 |
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size). |
9.000 |
Cu. Metr |
NA |
ITM000911077
25
82 |
47.2 |
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
14.000 |
Cu. Metr |
NA |
ITM000911078
25
83 |
48.1 |
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). |
45.000 |
Cu. Metr |
NA |
ITM000911079
29
84 |
49.1 |
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
2300.000 |
K.G.s |
NA |
ITM000911080
25
85 |
50 |
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
80.000 |
Cu. Metr |
NA |
ITM000911081
25
86 |
51.1.1 |
CARRIAGE OF MATERIALS By Mechanical Transport including loading, unloading and stacking upto 2 km Lime, moorum, building rubbish |
50.000 |
Cu. Metr |
NA |
ITM000911082
25
87 |
51.1.2 |
CARRIAGE OF MATERIALS By Mechanical Transport including loading, unloading and stacking upto 2 km. Earth |
70.000 |
Cu. Metr |
NA |
ITM000911083
25
88 |
51.1.3 |
CARRIAGE OF MATERIALS By Mechanical Transport including loading, unloading and stacking upto 2 km. Excavated rock |
50.000 |
Cu. Metr |
NA |
ITM000911085
25
89 |
51.1.4 |
CARRIAGE OF MATERIALS By Mechanical Transport including loading, unloading and stacking upto 2 km Soling stone |
50.000 |
Cu. Metr |
NA |
ITM000911086
25
90 |
52.1 |
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
800.000 |
Cu. Metr |
NA |
ITM000911088
25
91 |
53.1 |
Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. Ordinary rock |
120.000 |
Cu. Metr |
NA |
ITM000911089
25
92 |
53.2 |
Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. Hard rock (blasting prohibited) |
80.000 |
Cu. Metr |
NA |
ITM000911090
23
93 |
54.1 |
Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge: All kinds of soil |
1200.000 |
Sq.Metr |
NA |
ITM000911092
25
94 |
55.1 |
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
230.000 |
Cu. Metr |
NA |
ITM000911096
25
95 |
56 |
Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete. |
130.000 |
Cu. Metr |
NA |
ITM000911100
25
96 |
57.1.1 |
Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level Concrete of M30 grade with minimum cement content of 350 kg /cum |
190.000 |
Cu. Metr |
NA |
ITM000911101
25
97 |
58.1.1 |
Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately) All works above plinth level upto floor V level Concrete of M30 grade with minimum cement content of 350 kg /cum |
260.000 |
Cu. Metr |
NA |
ITM000911102
25
98 |
59.1.1 |
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately) All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum |
1.500 |
Cu. Metr |
NA |
ITM000911103
23
99 |
60.1 |
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete |
800.000 |
Sq.Metr |
NA |
ITM000911106
23
100 |
60.2 |
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
550.000 |
Sq.Metr |
NA |
ITM000911161
23
101 |
60.3 |
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Suspended floors, roofs, landings, balconies and access platform |
750.000 |
Sq.Metr |
NA |
ITM000911163
23
102 |
60.4 |
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers |
270.000 |
Sq.Metr |
NA |
ITM000911165
23
103 |
60.5 |
Centering and shuttering including strutting, propping etc. and removal of form for all heights :Columns, Pillars, Piers, Abutments, Posts and Struts |
100.000 |
Sq.Metr |
NA |
ITM000911167
29
104 |
61.1 |
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
13000.000 |
K.G.s |
NA |
ITM000911174
29
105 |
62.1 |
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. |
16600.000 |
K.G.s |
NA |
ITM000911178
25
106 |
63.1 |
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
60.000 |
Cu. Metr |
NA |
ITM000911183
23
107 |
64.1 |
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
55.000 |
Sq.Metr |
NA |
ITM000911190
25
108 |
65.1 |
Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand) |
30.000 |
Cu. Metr |
NA |
ITM000911191
23
109 |
66 |
18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge. |
550.000 |
Sq.Metr |
NA |
ITM000911193
23
110 |
67.1 |
12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) |
700.000 |
Sq.Metr |
NA |
ITM000911195
23
111 |
68.1 |
6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
600.000 |
Sq.Metr |
NA |
ITM000911196
23
112 |
69 |
Neat cement punning. |
260.000 |
Sq.Metr |
NA |
ITM000911197
23
113 |
70.1 |
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer |
450.000 |
Sq.Metr |
NA |
ITM000911199
23
114 |
71.1 |
Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm) |
480.000 |
Sq.Metr |
NA |
ITM000911201
23
115 |
72.1 |
Applying priming coats with primer of approved brand and manufacture, low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface VOC content less than 50 grams/litre |
720.000 |
Sq.Metr |
NA |
ITM000911204
23
116 |
73.1 |
Wall painting with acrylic emulsion paint, VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour Two coats |
720.000 |
Sq.Metr |
NA |
ITM000911205
23
117 |
74.1 |
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
700.000 |
Sq.Metr |
NA |
ITM000911206
29
118 |
75.1.1 |
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) |
140.000 |
K.G.s |
NA |
ITM000911207
29
119 |
75.2.1 |
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
190.000 |
K.G.s |
NA |
ITM000911209
23
120 |
76.1 |
Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side |
5.000 |
Sq.Metr |
NA |
ITM000911210
23
121 |
77.1 |
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness |
20.000 |
Sq.Metr |
NA |
ITM000911214
23
122 |
77.2 |
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness |
5.000 |
Sq.Metr |
NA |
ITM000911215
31
123 |
78.1 |
Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600 Upto 5mm depth and 5 mm width |
70.000 |
Metre |
NA |
ITM000911216
31
124 |
78.2 |
Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600 Upto 10 mm depth and 10 mm width |
70.000 |
Metre |
NA |
ITM000911218
47
125 |
79 |
Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
2.000 |
Each |
NA |
ITM000911220
47
126 |
80.1 |
Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-incharge Powder coated minimum thickness 50 micron aluminium |
4.000 |
Each |
NA |
ITM000911221
29
127 |
81 |
Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). |
15.000 |
K.G.s |
NA |
ITM000911222
23
128 |
82.1 |
Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading |
9.000 |
Sq.Metr |
NA |
ITM000911224
47
129 |
83.1 |
Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 125x64x1.90 mm |
10.000 |
Each |
NA |
ITM000911225
47
130 |
84.1 |
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm |
3.000 |
Each |
NA |
ITM000911270
47
131 |
85.1 |
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm |
8.000 |
Each |
NA |
ITM000911275
47
132 |
85.2 |
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm |
8.000 |
Each |
NA |
ITM000911278
47
133 |
85.3 |
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 100x10 mm |
6.000 |
Each |
NA |
ITM000911279
47
134 |
86.1 |
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm |
8.000 |
Each |
NA |
ITM000911280
47
135 |
87.1 |
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper |
4.000 |
Each |
NA |
ITM000911289
23
136 |
88.1 |
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
7.000 |
Sq.Metr |
NA |
ITM000911293
23
137 |
89 |
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
13.000 |
Sq.Metr |
NA |
ITM000911295
23
138 |
90 |
Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete. |
3.000 |
Sq.Metr |
NA |
ITM000911297
31
139 |
91.1 |
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase |
100.000 |
Metre |
NA |
ITM000916608
31
140 |
92.1 |
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter |
6.000 |
Metre |
NA |
ITM000916609
31
141 |
92.2 |
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter |
30.000 |
Metre |
NA |
ITM000916610
47
142 |
93.1.1 |
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door 110x110x110 mm |
3.000 |
Each |
NA |
ITM000916611
47
143 |
93.2.1 |
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5 75 mm bend |
4.000 |
Each |
NA |
ITM000916612
47
144 |
93.2.2 |
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5 110 mm bend |
8.000 |
Each |
NA |
ITM000916613
47
145 |
93.3.1 |
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe |
8.000 |
Each |
NA |
ITM000916614
47
146 |
94.1 |
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm |
5.000 |
Each |
NA |
ITM000916615
47
147 |
94.2 |
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm |
12.000 |
Each |
NA |
ITM000916616
47
148 |
95 |
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. |
2.000 |
Each |
NA |
ITM000916617
31
149 |
96.1 |
Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter |
15.000 |
Metre |
NA |
ITM000916619
31
150 |
96.2 |
Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 200 mm diameter |
300.000 |
Metre |
NA |
ITM000916620
31
151 |
97.1 |
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150 mm diameter S.W. pipe |
15.000 |
Metre |
NA |
ITM000916621
31
152 |
97.2 |
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 200 mm diameter S.W. pipe |
300.000 |
Metre |
NA |
ITM000916622
47
153 |
98.1.1 |
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
2.000 |
Each |
NA |
ITM000916623
47
154 |
99.1.1 |
Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 0.91 m deep with SFRC cover and frame (heavy duty, HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
10.000 |
Each |
NA |
ITM000916624
31
155 |
100.1 |
Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
10.000 |
Metre |
NA |
ITM000916627
47
156 |
101 |
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and manufacture s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
100.000 |
Each |
NA |
ITM000916629
47
157 |
102.1 |
Supplying and fixing C.I. cover without frame for manholes 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg |
4.000 |
Each |
NA |
ITM000918917
31
158 |
103.1.1 |
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes |
6.000 |
Metre |
NA |
ITM000918919
31
159 |
103.1.2 |
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes |
6.000 |
Metre |
NA |
ITM000918920
31
160 |
104.1.1 |
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 32 mm nominal outer dia Pipes |
15.000 |
Metre |
NA |
ITM000918921
47
161 |
105.1 |
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore |
2.000 |
Each |
NA |
ITM000918922
47
162 |
106.1 |
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
2.000 |
Each |
NA |
ITM000918923
47
163 |
107.1 |
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore |
3.000 |
Each |
NA |
ITM000918924
47
164 |
108.1 |
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
1.000 |
Each |
NA |
ITM000918925
47
165 |
109.1 |
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
1.000 |
Each |
NA |
ITM000918926
47
166 |
110.1 |
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
2.000 |
Each |
NA |
ITM000918927
47
167 |
111.1 |
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm |
2.000 |
Each |
NA |
ITM000918928
47
168 |
112.1 |
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
3.000 |
Each |
NA |
ITM000918929
47
169 |
113.1 |
Providing and fixing PTMT urinal cock of approved quality and colour. 15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms |
1.000 |
Each |
NA |
ITM000919578
31
170 |
114.1.1 |
Providing and fixing soil, waste and vent pipes : 100 mm dia Centrifugally cast iron ( s p u n ) socket & spigot (S&S) pipe as per IS: 3989 |
10.000 |
Metre |
NA |
ITM000919582
47
171 |
115.1.1 |
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia Sand cast iron S&S as per IS - 3989 |
10.000 |
Each |
NA |
ITM000919584
47
172 |
116.1.1 |
Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as per IS : 3989 |
10.000 |
Each |
NA |
ITM000919587
47
173 |
117.1.1 |
Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm Sand cast iron S&S as per IS - 3989 |
5.000 |
Each |
NA |
ITM000919588
25
174 |
118.1 |
Grading roof for water proofing treatment with Cement mortar 1:4 (1cement : 4 coarse sand) |
40.000 |
Cu. Metr |
NA |
ITM000919592
29
175 |
119 |
Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer s specification. |
310.000 |
K.G.s |
NA |
ITM000919594
29
176 |
120 |
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
90.000 |
K.G.s |
NA |
ITM000919596
29
177 |
121 |
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
1300.000 |
K.G.s |
NA |
ITM000919598
23
178 |
122.1 |
Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover |
15.000 |
Sq.Metr |
NA |
ITM000919599
47
179 |
123 |
Providing and fixing ball bearing for rolling shutters. |
4.000 |
Each |
NA |
ITM000919601
23
180 |
124.1 |
Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area |
12.000 |
Sq.Metr |
NA |
ITM000919606
47
181 |
125 |
Providing and fixing PTMT soap Dish Holder length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
2.000 |
Each |
NA |
ITM000919611
47
182 |
126.1 |
Supply and fixing ---- of cast iron body with --- Nos inlet couplings complete with cap and chain as required for 150mm dia MS pipe connection, conforming to IS 904 as required. Make: Mini Max / Safex / Newage / Winco / Newtech / Padmini / Kartar 2Way Fire brigade connection cast iron body with 2 Nos Gun metal male instantaneous |
2.000 |
Each |
NA |
ITM000919613
34
183 |
127 |
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
1000.000 |
Litre |
NA |
ITM000919617
47
184 |
128.1.1 |
DISTRIBUTION BOARDS LIGHTING DB S 6 Way TPN DB consisting of (Pump room & Operator room LPDB) INCOMING: 40A TPN MCB - 1No. OUTGOING: 18nos. 16A SP MCB s SUPPLY & ERECTION |
2.000 |
Each |
NA |
ITM000919618
31
185 |
129.1.1 |
Supply, laying,testing & commissioning of the power cable of 1100V grade PVC aluminium armoured cable. The rates quoted shall be for laying indoor only, with GI pipe provided from DB s to ground level upto 2mtrs length of pipe. NOTE: Provide 150mm long extension bus strip from main incoming MCCB for termination of the main incoming cable.(No cable shall be terminated on the main incoming switch.) 4 Core x 6 sq.mm Al.Ar. Cable SUPPLY & LAYING |
30.000 |
Metre |
NA |
ITM000919619
31
186 |
129.2.1 |
Supply, laying,testing & commissioning of the power cable of 1100V grade PVC aluminium armoured cable. The rates quoted shall be for laying indoor only, with GI pipe provided from DB s to ground level upto 2mtrs length of pipe. NOTE: Provide 150mm long extension bus strip from main incoming MCCB for termination of the main incoming cable.(No cable shall be terminated on the main incoming switch.) 4 Core x 4 sq.mm Cu.Ar. Cable SUPPLY & LAYING |
60.000 |
Metre |
NA |
ITM000919621
47
187 |
130.1 |
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. including copper cable lugs, Single compression brass cable glands, tapping, crimping, etc., complete as required. 3 X 150 sq. mm (50mm) |
28.000 |
Each |
NA |
ITM000919622
47
188 |
130.2 |
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. including copper cable lugs, Single compression brass cable glands, tapping, crimping, etc., complete as required. 2R x 3 X 120 sq. mm (45mm) |
24.000 |
Each |
NA |
ITM000919624
47
189 |
130.3 |
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. including copper cable lugs, Single compression brass cable glands, tapping, crimping, etc., complete as required. 12C X2.5 Sq.mm for Diesel Engine |
24.000 |
Each |
NA |
ITM000919626
47
190 |
130.4 |
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. including copper cable lugs, Single compression brass cable glands, tapping, crimping, etc., complete as required. 2C X 2.5 Sq.mm for Instrumentation |
8.000 |
Each |
NA |
ITM000919630
47
191 |
130.5 |
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. including copper cable lugs, Single compression brass cable glands, tapping, crimping, etc., complete as required. 3 C X 4.0 Sq.mm for Start /Stop push button |
12.000 |
Each |
NA |
ITM000919634
47
192 |
130.6 |
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. including copper cable lugs, Single compression brass cable glands, tapping, crimping, etc., complete as required. 4 C X 6.0 Sq.mm Cu.cable for Pump room DB |
16.000 |
Each |
NA |
ITM000919635
47
193 |
130.7 |
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. including copper cable lugs, Single compression brass cable glands, tapping, crimping, etc., complete as required. 4 C X 4.0 Sq.mm Cu.cable for Operator room DB |
16.000 |
Each |
NA |
ITM000919638
31
194 |
131.1 |
Supply and laying of 1100V grade FRLS insulated, copper conductor cables in 2mm thick FRLS MS conduits, run on surface of the ceiling \ above the false ceiling, concealed in the wall or partition, saddles at every 600mm c/c. A separate neutral shall be run for each circuit. The rate shall include all fixing accessories like collars, tees, elbows, providing fan hooks, ceiling roses, holders, wooden blocks,switches,sockets, switch mounting MS boxes, etc., of approved make. NOTE: All MS Conduits should be as per IS only Supply and laying of 2 runs of 2.5 Sq.mm. PVCinsulated copper conductor cable (Secondary Wiring) Run in a 25mm dia. MS conduiton surface of the ceiling or in wall or floor or partition SUPPLY & LAYING |
60.000 |
Metre |
NA |
ITM000919640
31
195 |
131.2.1 |
Supply and laying of 1100V grade FRLS insulated, copper conductor cables in 2mm thick FRLS MS conduits, run on surface of the ceiling \ above the false ceiling, concealed in the wall or partition, saddles at every 600mm c/c. A separate neutral shall be run for each circuit. The rate shall include all fixing accessories like collars, tees, elbows, providing fan hooks, ceiling roses, holders, wooden blocks,switches,sockets, switch mounting MS boxes, etc., of approved make. NOTE: All MS Conduits should be as per IS only Supply and laying of 2 runs of 4.0 Sq.mm. PVC insulated copper conductor cable (Primary Wiring) Run in a 25mm dia. MS conduit on surface of the ceiling or in wall or floor or partition SUPPLY & LAYING |
25.000 |
Metre |
NA |
ITM000919643
31
196 |
131.3.1 |
Supply and laying of 1100V grade FRLS insulated, copper conductor cables in 2mm thick FRLS MS conduits, run on surface of the ceiling above the false ceiling, concealed in the wall or partition, saddles at every 600mm c/c. A separate neutral shall be run for each circuit. The rate shall include all fixing accessories like collars, tees, elbows, providing fan hooks, ceiling roses, holders, wooden blocks,switches,sockets, switch mounting MS boxes, etc., of approved make. NOTE: All MS Conduits should be as per IS only Supply and laying of 4 X 10 sq. mm + 2 X 6 sq. mm earth wire PVC insulated copper conductor cable (Power Wiring) Run in a 25mm dia. MS conduit on surface of the ceiling or in wall or floor or partition SUPPLY & LAYING |
10.000 |
Metre |
NA |
ITM000919644
47
197 |
132.1.1 |
Supply and laying of 3 runs of 1.5 Sqmm of 1100V grade PVC insulated FRLS copper wire run in a 25mm dia. MS conduit of not less than 2mm thick, the rate shall include all fixing accessories like collars,tees, elbows, providing fan hooks, ceiling roses, holder,wooden blocks, switches,sockets,switch switch mounting MS boxes, etc, of approved make. Single light point controlled by a 6A piano key type switch LEGRAND - MYRIUS SUPPLY & ERECTION |
10.000 |
Each |
NA |
ITM000919646
47
198 |
132.2.1 |
Supply and laying of 3 runs of 1.5 Sqmm of 1100V grade PVC insulated FRLS copper wire run in a 25mm dia. MS conduit of not less than 2mm thick, the rate shall include all fixing accessories like collars,tees, elbows, providing fan hooks, ceiling roses, holder,wooden blocks, switches,sockets,switch switch mounting MS boxes, etc, of approved make. Two light points controlled by a 6A piano key type switch. LEGRAND - MYRIUS SUPPLY & ERECTION |
25.000 |
Each |
NA |
ITM000919658
47
199 |
132.3.1 |
Supply and laying of 3 runs of 1.5 Sqmm of 1100V grade PVC insulated FRLS copper wire run in a 25mm dia. MS conduit of not less than 2mm thick, the rate shall include all fixing accessories like collars,tees, elbows, providing fan hooks, ceiling roses, holder,wooden blocks, switches, sockets, switch mounting MS boxes, etc, of approved make. Three light points controlled by a 6A piano key type switch. LEGRAND - MYRIUS SUPPLY & ERECTION |
5.000 |
Each |
NA |
ITM000919663
47
200 |
132.4.1 |
Supply and laying of 3 runs of 1.5 Sqmm of 1100V grade PVC insulated FRLS copper wire run in a 25mm dia. MS conduit of not less than 2mm thick, the rate shall include all fixing accessories like collars,tees, elbows, providing fan hooks, ceiling roses, holder,wooden blocks, switches, sockets, switch mounting MS boxes, etc, of approved make. Four light points controlled by a 6A piano key type switch. LEGRAND - MYRIUS SUPPLY & ERECTION |
25.000 |
Each |
NA |
ITM000919666
47
201 |
132.5.1 |
Supply and laying of 3 runs of 1.5 Sqmm of 1100V grade PVC insulated FRLS copper wire run in a 25mm dia. MS conduit of not less than 2mm thick, the rate shall include all fixing accessories like collars,tees, elbows, providing fan hooks, ceiling roses, holder,wooden blocks, switches,sockets,switch switch mounting MS boxes, etc, of approved make. Single light point controlled by 2 way piano key type switches. (Two way point) LEGRAND - MYRIUS SUPPLY & ERECTION |
1.000 |
Each |
NA |
ITM000919668
47
202 |
132.6.1 |
Supply and laying of 3 runs of 1.5 Sqmm of 1100V grade PVC insulated FRLS copper wire run in a 25mm dia. MS conduit of not less than 2mm thick, the rate shall include all fixing accessories like collars,tees, elbows, providing fan hooks, ceiling roses, holder,wooden blocks, switches,sockets,switch switch mounting MS boxes, etc, of approved make. Ceiling fan point controlled by 6A piano key type switch along with an electronic STEPPED DOWN fan regulator. LEGRAND - MYRIUS SUPPLY & ERECTION |
2.000 |
Each |
NA |
ITM000919671
47
203 |
132.7.1 |
Supply and laying of 3 runs of 1.5 Sqmm of 1100V grade PVC insulated FRLS copper wire run in a 25mm dia. MS conduit of not less than 2mm thick, the rate shall include all fixing accessories like collars,tees, elbows, providing fan hooks, ceiling roses, holder,wooden blocks, switches,sockets,switch switch mounting MS boxes, etc, of approved make. 6A, 5pin socket located along with the other switches (dependent socket) inclusive of control switches & connecting wire. LEGRAND - MYRIUS SUPPLY & ERECTION |
5.000 |
Each |
NA |
ITM000919673
47
204 |
132.8.1 |
Supply and laying of 3 runs of 1.5 Sqmm of 1100V grade PVC insulated FRLS copper wire run in a 25mm dia. MS conduit of not less than 2mm thick, the rate shall include all fixing accessories like collars,tees, elbows, providing fan hooks, ceiling roses, holder,wooden blocks, switches,sockets, switch mounting MS boxes, etc, of approved make. 6A, 5pin socket (independent socket) inclusive of control wiring LEGRAND - MYRIUS SUPPLY & ERECTION |
5.000 |
Each |
NA |
ITM000919675
47
205 |
133.1 |
Supply, erection, testing and commissioning of switches & sockets of approved make mounted surface on wall / concealed in the wall including necessary fixing accessories like GI box, sockets plates etc., complete as required by the engineer-in-charge.The rate shall include the terminations of the wire. 16A, 6 pin socket outlet controlled by a 16A SP switch, for supply & erection.(RAW POWER) LEGRAND - MYRIUS |
4.000 |
Each |
NA |
ITM000919676
47
206 |
133.2.1 |
Supply, erection, testing and commissioning of switches & sockets of approved make mounted surface on wall / concealed in the wall including necessary fixing accessories like GI box, sockets plates etc., complete as required by the engineer-in-charge.The rate shall include the terminations of the wire. Supply and providing 100A TP MCCB with metal enclosure with indication lamps,ammeter & voltmeter, etc., complete as required by the Engineer-in-charge. SUPPLY & ERECTION |
2.000 |
Each |
NA |
ITM000919678
47
207 |
134.1.1 |
Supply,Assembly,installation,testing & commissioning of the following fixtures with all required accessories like screws, connectors,lamps, connection wires, ball & socket, wooden block termination & brick pedestal for street light poles,pathway lights & garden lights etc., complete, as required by the engineer-in- charge. Supply,fixing testing & commissioning 1 x 36W LED Tube light fixture suspended from the ceiling with supporting fixing accessories as required by the engineer-in-charge (4 feet LENGTH) SUPPLY & ERECTION |
2.000 |
Each |
NA |
ITM000919682
47
208 |
134.2.1 |
Supply,Assembly,installation,testing & commissioning of the following fixtures with all required accessories like screws, connectors,lamps, connection wires, ball & socket, wooden block termination & brick pedestal for street light poles,pathway lights & garden lights etc., complete, as required by the engineer-in- charge. Supply,fixing testing & commissioning 1 x 18W LED Surface light fixture with lamp fixed to the ceiling with supporting fixing accessories as required by the engineer-in-charge SUPPLY & ERECTION |
28.000 |
Each |
NA |
ITM000919685
47
209 |
134.3.1 |
Supply,Assembly,installation,testing & commissioning of the following fixtures with all required accessories like screws, connectors,lamps, connection wires, ball & socket, wooden block termination & brick pedestal for street light poles,pathway lights & garden lights etc., complete, as required by the engineer-in- charge. Supply,fixing testing & commissioning 1 x 15W Surface light fixture with lamp fixed to the ceiling with fixing accessories as required by the engineer-in-charge SUPPLY & ERECTION |
2.000 |
Each |
NA |
ITM000919688
47
210 |
135 |
Supply of 48 inch (1200mm) Sweep decorative Ceiling Fan 1 Star Rated with all accessories etc., complete. Makes : Crompton / Havells / Orient |
2.000 |
Each |
NA |
ITM000919692
47
211 |
136 |
Supply of 24 inch (600mm)-Wall mounting / Pedestal Air Circulators Makes : Crompton / Havells Turbo Force / Orient / Almonard / Panasonic / Halonix / RR. |
4.000 |
Each |
NA |
ITM000919694
47
212 |
137 |
Supply of 12 inch (300mm), 900 RPM Heavy duty exhaust fan with metallic blades. Makes : Crompton / Almonard / Havells Turbo Force SP. |
2.000 |
Each |
NA |
ITM000919698
47
213 |
138.1 |
EARTHING. Providing and fixing GI pipe earth station confirming fully to IS 3043 complete with brick masonary chamber including plastering, CI cover, watering funnel, clamps, chemicals etc., complete as required by the engineer-in-charge. The rate shall include the excavation of earth in all sorts of soil. |
8.000 |
Each |
NA |
ITM000919704
47
214 |
138.2 |
EARTHING. Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required |
2.000 |
Each |
NA |
ITM000919707
31
215 |
139.1 |
Supply & laying of GI tapes, wires with necessary accessories like clamps, screws, nuts and bolts etc., complete, inclusive of termination. 25mm x 6mm GI tape. |
40.000 |
Metre |
NA |
ITM000919709
31
216 |
140 |
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
15.000 |
Metre |
NA |
ITM000919712
47
217 |
141.1 |
Supply and Transportation of 1.00 HP Single phase open well ISI submersible motor pumpset. Makes: Kirloskar / Crompton / Texmo / CRI / KSB / Aryan Varsha |
1.000 |
Each |
NA |
ITM000919715
47
218 |
142 |
Supply and Transportation of control panel for single phase submersible motors up to 3 HP @ 220V 50Hz operating range between 80 to 240V including supply and fixing of Direct - on - Line LTLK / SIEMENS / CROMPTON make Volt meter and Ammeter with starting and running capacitors assembled with ISI mark contactors and fitted with Legrand make ISI mark MCB etc., complete. |
1.000 |
Each |
NA |